Owon SDS1000 User Manual Download Page 42 | Manualshive

Page: 42 / 68

background image

4.Advanced User Guidebook

37

from the input connector. Push the

Utility

button, select

Function

in the right

menu, the function menu will display at the left, select

Adjust

. If everything is

ready, select

Self Cal

in the right menu to enter the self-calibration procedure of

the instrument.

Probe checking

To  check  whether  probe  attenuation  is  good.  The  results  contain  three
circumstances:  Overflow  compensation,  Good  compensation,  Inadequate
compensation.  According  to  the  checking  result,  users  can  adjust  probe
attenuation to the best. Operation steps are as follows:
1.  Connect the probe to CH1, adjust the probe attenuation to the maximum.
2.  Push the

Utility

button, select

Function

in the right menu, select

Adjust

in the

left menu.

3. Select

ProbeCh.

in the right menu, tips about probe checking shows on the

screen.

4. Select

ProbeCh.

again to begin probe checking and the checking result will

occur after 3s; push any other key to quit.

●

Save

You can save the waveforms, configures or screen images. Refer to "

and Recall a Waveform

" on page 29.

●

Update

Use the front-panel USB port to update your instrument firmware using a USB
memory device. Refer to "

How to Update your Instrument Firmware

" on page 37.

How to Update your Instrument Firmware

Use the front-panel USB port to update your instrument firmware using a USB
memory device.

USB memory device requirements

: Insert a USB memory device into the USB

port on the front panel. If the icon

appears on the top right of the screen, the

USB memory device is installed successfully. If the USB memory device cannot be
detected, format the USB memory device according to the methods in "

Caution

: Updating your instrument firmware is a sensitive operation, to prevent

damage to the instrument, do not power off the instrument or remove the USB
memory device during the update process.

To update your instrument firmware, do the following:

1. Push the

Utility

button, select

Function

in the right menu, select

Configure

in

the left menu, select

About

in the right menu. View the model and the currently

installed firmware version.

2. From a PC, visit the website and check if the website offers a newer firmware

version. Download the firmware file. The file name must be Scope.update.

«
...
40
41
42
43
44
...
»

Summary of Contents for SDS1000





































































Reviews:

No comments

Related manuals for SDS1000

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brand: J&M Pages: 33

Brand: Tascam Pages: 8

Brand: Keithley Pages: 79

Brand: Kayakpro Pages: 17

Brand: Yoshitake Pages: 11

Brand: H&S Pages: 42

Brand: ParaBody Pages: 3

Brand: Valiani Pages: 66

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

Brand: ZacUrate Pages: 2

Brand: ZacUrate Pages: 2

Brand: Coba Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands