Owon SDS1000 User Manual Download Page 28

Page: 28 / 68

4.Advanced User Guidebook

aliasing. So pay more attention to the relation between the frequency being
sampled and measured.

Use Vertical Position and Scale Knobs

1. The

Vertical Position

knob is used to adjust the vertical positions of the

waveforms.
The  analytic  resolution  of  this  control  knob  changes  with  the  vertical
division.

2. The

Vertical Scale

knob is used to regulate the vertical resolution of the

wave forms. The sensitivity of the vertical division steps as 1-2-5.

The vertical position and vertical resolution is displayed at the left bottom
corner of the screen (see

Figure 4-1

Figure 4-1 Information about Vertical Position

How to Set the Horizontal System

The

HORIZONTAL CONTROLS

includes the

Horizontal HOR

button and

such knobs as

Horizontal Position

and

Horizontal Scale

Horizontal Position

knob: this knob is used to adjust the horizontal

positions of all channels (include those obtained from the mathematical
manipulation), the analytic resolution of which changes with the time base.

Horizontal Scale

knob: it is used to set the horizontal scale factor for

setting the main time base or the window.

Horizontal HOR

button: push it to switch between the normal mode and

the wave zoom mode. For more detailed operations, see the introductions

Summary of Contents for SDS1000





































































Search results

Summary of Contents for SDS1000

Reviews:

Related manuals for SDS1000

Brands by name

Popular brands

Owon SDS1000, User Manual

Search results

Summary of Contents for SDS1000

Reviews:

Related manuals for SDS1000

Brands by name

Popular brands