Owon SDS1000 User Manual Download Page 21 | Manualshive

Page: 21 / 68

background image

4.Advanced User Guidebook

16

4. Advanced User Guidebook

This chapter will deal with the following topics mainly:



How to Set the Vertical System



How to Set the Horizontal System



How to Set the Trigger System



How to Set the Sampling/Display



How to Save and Recall Waveform



How to Implement the Auxiliary System Function Setting



How to Update your Instrument Firmware



How to Measure Automatically



How to Measure with Cursors



How to Use Executive Buttons

It is recommended that you read this chapter carefully to get acquainted the
various measurement functions and other operation methods of the
oscilloscope.

«
...
19
20
21
22
23
...
»

Summary of Contents for SDS1000





































































Reviews:

No comments

Related manuals for SDS1000

Brand: iGuzzini Pages: 20

Brand: Haki Pages: 24

Brand: Dakota Digital Pages: 5

Brand: Danelec Pages: 67

Brand: Farmi Forest Corporation Pages: 32

GPSMAP 188 Sounder

Brand: Garmin Pages: 134

Brand: jablotron Pages: 2

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: K-LASER Pages: 70

Brand: K-LASER Pages: 72

NI VISION PCI-8254R

Brand: National Instruments Pages: 13

NI VISION PCI-8254R

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 39

Brand: National Instruments Pages: 65

Brand: haacon Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands