Owon SDS1000 User Manual Download Page 16

Page: 16 / 68

3.Quick Start

compensation is achieved (see

Figure 3-6

and

Figure 3-7

Overcompensated

Compensated correctly

Under

compensated

Figure 3-6 Displayed Waveforms of the Probe Compensation

3. Repeat the steps mentioned if needed.

Figure 3-7 Adjust Probe

How to Set the Probe Attenuation Coefficient

The probe has several attenuation coefficients, which will influence the vertical
scale factor of the oscilloscope.

To change or check the probe attenuation coefficient in the menu of
oscilloscope:

(1)

Push the function menu button of the used channels (

CH1

CH4 button

(2)

Select

Probe

in the right menu; turn the

knob to select the proper value

in the left menu corresponding to the probe.

This setting will be valid all the time before it is changed again.

Caution:

The default attenuation coefficient of the probe on the instrument is
preset to 10X.

Make sure that the set value of the attenuation switch in the probe is
the same as the menu selection of the probe attenuation coefficient in
the oscilloscope.

The set values of the probe switch are 1X and 10X (see

Figure 3-8

Summary of Contents for SDS1000





































































Search results

Summary of Contents for SDS1000

Reviews:

Related manuals for SDS1000

Brands by name

Popular brands

Owon SDS1000, User Manual

Search results

Summary of Contents for SDS1000

Reviews:

Related manuals for SDS1000

Brands by name

Popular brands