Step 6
Located holes in centre of beams(
Ⓐ
and
Ⓑ
)
*Place centre louver
Ⓗ
into
12th slot
, lining up with the holes for 300x300cm
size.*
Place centre louver
Ⓗ
into
16th slot
, lining up with the holes for 300x400cm.
Using M10 nut
⑤
X2, secure the louver in place
Place Driving louver
Ⓘ
in line with
4th slot
on the beam
Ⓐ
and
Ⓑ
.
Fit all common louvers
Ⓖ
X21 for 300x300cm and
Ⓖ
X30 for 300x400cm size into
the remaining slots in the beams
Step 7
Fix
Ⓙ
x 2 (flat L-shaped aluminum profile).
11
1
8
3
1
8
3
1
8
3
9
9
9
9
9
9
10
11
11
Step 6
Located holes in centre of beams(
Ⓐ
and
Ⓑ
)
*Place centre louver
Ⓗ
into
12th slot
, lining up with the holes for 300x300cm
size.*
Place centre louver
Ⓗ
into
16th slot
, lining up with the holes for 300x400cm.
Using M10 nut
⑤
X2, secure the louver in place
Place Driving louver
Ⓘ
in line with
4th slot
on the beam
Ⓐ
and
Ⓑ
.
Fit all common louvers
Ⓖ
X21 for 300x300cm and
Ⓖ
X30 for 300x400cm size into
the remaining slots in the beams
Step 7
Fix
Ⓙ
x 2 (flat L-shaped aluminum profile).
11
Step 6
Located holes in centre of beams(
Ⓐ
and
Ⓑ
)
*Place centre louver
Ⓗ
into
12th slot
, lining up with the holes for 300x300cm
size.*
Place centre louver
Ⓗ
into
16th slot
, lining up with the holes for 300x400cm.
Using M10 nut
⑤
X2, secure the louver in place
Place Driving louver
Ⓘ
in line with
4th slot
on the beam
Ⓐ
and
Ⓑ
.
Fit all common louvers
Ⓖ
X21 for 300x300cm and
Ⓖ
X30 for 300x400cm size into
the remaining slots in the beams
Step 7
Fix
Ⓙ
x 2 (flat L-shaped aluminum profile).
11
Step 6
Located holes in centre of beams(
Ⓐ
and
Ⓑ
)
*Place centre louver
Ⓗ
into
12th slot
, lining up with the holes for 300x300cm
size.*
Place centre louver
Ⓗ
into
16th slot
, lining up with the holes for 300x400cm.
Using M10 nut
⑤
X2, secure the louver in place
Place Driving louver
Ⓘ
in line with
4th slot
on the beam
Ⓐ
and
Ⓑ
.
Fit all common louvers
Ⓖ
X21 for 300x300cm and
Ⓖ
X30 for 300x400cm size into
the remaining slots in the beams
Step 7
Fix
Ⓙ
x 2 (flat L-shaped aluminum profile).
11
One for each other of the slats is required.
*Use bolt
⑥
x46, plastic spacer
⑦
x46 and nut
⑧
x46 to tighten for 300x300 cm.*
Use bolt
⑥
x64, plastic spacer
⑦
x64 and nut
⑧
x64 to tighten for 300x400 cm.
Secure the louvers at each end.
NOTE: Do not over tighten. Over tightening will prevent louvers from moving.
Step 8
Mark holes for expansion bolt
⑩
x4 on each post.
Note: the drill size should be 12 mm.
Insert the bolts. Use an hammer drill if necessary. Place the posts
over the bolts. Tighten the nuts.
Once installed, make sure any remaining plastic is removed and silicone is used along
all corners and gutters to waterproof.
Tight nuts
12
(WDSH
)L[DWLRQDXVRO
6WHS
)ORUHIL[DWLRQ
6WHS
)ORUHIL[DWLRQ
Summary of Contents for ATHENES
