Part Number 10400117-101 04/2007
©2007 Overland Storage, Inc.
W
Page 2 of 2
IMPORTANT: If the old unit didn’t power down with the
shuttle parked, contact Overland Technical Support.
Secure the Robotics
CAUTION:
Units that do not have the four holes
underneath for the well nuts and screws must use the
enclosed Wire Tie-Down kit to secure the robotics before
packaging the unit.
For units with the four holes, follow this procedure:
1.
Attach the
old drive cover
to the old chassis.
2.
Open the
left door
.
3.
Install the
shuttle bracket
:
a.
Holding the shuttle bracket by the
front lip
), slide it into the magazine bay.
Figure 3. Inserting the Shuttle Bracket
b. Swing the rear
of the bracket to the
right
until it
contacts the shuttle.
c.
Press the
front lip
of the bracket down and to the
right until the screw holes align.
You should hear a click as the bracket slips into
place over the shuttle.
d.
Install the
screw
that holds the shuttle bracket to
the bottom edge of the front panel.
4.
Turn the unit onto its
left side
with the
front bezel
off the table
.
5.
Install the
shuttle bracket well nut
:
a.
With a
washer
on a
screw
, screw it onto a
well nut
until only one-half inch (12.5cm) remains extended.
b.
for the other
three
well nuts.
c.
While pressing the
shuttle bracket
down, visually
confirm the
hole alignment
from underneath.
d.
Insert a
well nut assembly
(
) through the
three holes using the extended screw as a handle.
Figure 4. Well Nut Insertion (Side View)
e.
While continuing to hold the bracket against the
shuttle, tighten the
screw
into the well nut.
6.
Insert the remaining
three well nut assemblies
using the extended screws, and tighten (
).
Figure 5. Installing the Well Nuts and Screws
7.
Carefully return the
library
to the upright position.
Repack the Chassis
Once the robotics are secure, repack the unit for shipment.
1.
Open the top of the box and remove all the
packaging
materials
stored there.
2.
With the ARCvault
on a secure surface, slide it into the
ESD bag
and seal with packing tape.
3.
Attach the
larger end caps
to the rear.
4.
Attach the
smaller end caps
to the front.
5.
Using two people, lower the
ARCvault
into the box.
6.
Tape the box
using the type of tape required by the
shipper for the shipping method being used.
All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be
used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that no right is conveyed to reproduce or have reproduced any item herein disclosed without express permission from
Overland Storage. Overland Storage provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make
improvements or changes in the product(s) or program(s) described in this document at any time. These changes will be incorporated in new editions of this publication.
Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.
Repackaging the Library
Bracket Front Lip
Well Nut
Bracket
Track Plate
Chassis
Correct
Incorrect
Shuttle
Stop Washer
A
RC
-0
04
8
Screws & Well Nuts
Shuttle Bracket Hole
Additional Help
You can get additional technical support on the Internet at http://support.overlandstorage.com, or call
1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).
