background image

c.

 

Diagram below shows how to use ladder buckle.

 

 

d.

 

Now run those straps up and through the ladder lock buckles sewn to the rear of 
the top.

 

e.

 

You now need to tighten and loosen the strap of the top so that it is centered 
correctly.

 

 

Cleaning and Storage Recommendations: 

1.

 

Before removing the Over Armour Cab for storage, make sure it is very clean in order to prevent 
scratching of the window panels.  Clean with a soft rag or sponge using a mild liquid detergent 
soap and warm water solution.  Never rub the windows with a dry cloth or rag!   Let the Cab dry 
thoroughly before attempting to roll for storage. 

 
2.

 

It is important that the Cab be rolled up for storage rather than folding.  Folding will cause 
damage to the windows!!!  Carefully roll up the Cab similar to the way it was when it was packed 
at the factory   On a large, clean and flat surface, fold the doors over the rear panel first, then, 
interleave the top and windshield on top of the doors.  Begin rolling the Cab into a roll 
approximately 8 inches in diameter.   Put the rolled Cab back into the carton for storage at a 
normal room temperature.  It is best not to expose the Cab to either extreme hot or cold 
temperatures when storing. 

 

 
3.

 

A special cleaner conditioner is available from Over Armour that will greatly increase the service 
life of the Cab Enclosure.  In addition, if additional hook and loop sets are needed, they can also 
be ordered.  

 

Summary of Contents for BC-3400-FC04







Reviews: