background image

E-122-8-E

1. BEFORE YOU BEGIN

When  you  received,  the  product  should  be  thoroughly  inspected  for  any  sign  of  damage  by  rough 

handling during transit.

1.1 Confirming the Tag

Product code and ratings appear on the counter tag. Make sure that the product you received complies 

with the specifications in your order.

General Specifications and Product Code Explanation appear on pages 24 and 25, respectively.

When  you  inquire,  supply  complete  information  as  to  the  product  name,  model  number, 

product number, ratings, etc.

1.2 Transportation Considerations

(1) The  OVAL  total  counter  can  best  be  transported  to  the  installation  site  in  the  shipping  container 

used for transit from our factory.

(2) Avoid giving impact shocks to the total counter during transit.

1.3 Storage Considerations

If the total counter upon receipt is to be stored for extended periods of time before installation, unexpected 

problems could arise. If such is the case, the following considerations should be taken:
(1) The total counter can best be stored in the original package used for transit from the factory.
(2) Select a storage location that meets the following requirements:

  ☆

Free from rainwater and moisture

  ☆

Least vibration and impact shock

  ☆

In the room temperature and humidity environment (around 25℃ and 65% R.H.)

A total counter which has been idle for extended periods of time may possibly require internal 

inspection. If such is the case, consult factory.

Tag (nameplate) shows ratings.

Fig.1.1 Tag Location

Summary of Contents for EL0122





























Reviews: