background image

OUTLINE S.R.L.

Via Leonardo da Vinci, 56

25020 Flero (Brescia) Italy

Tel.: +39 030.3581341

Fax +39 030.3580431

[email protected]

www.outline.it

25

13.  TECHNICAL CHARACTERISTICS

PHYSICAL

Component Low

2 x 10” NdFeB double r

efl

ex band-pass loaded woofer

Component Midrange

2 x 8” NdFeB partially horn loaded mid woofer

Component High

1 x 3” diaphragm NdFeB compression driver, DPRWG loaded

Connectors

2 x LKI8 in parallel (8-pin, military grade)

Cabinet Material

Baltic birch plywood

Cabinet Finish

Black polyurea coating

Grill

Epoxy powder coated

Rigging

Integrated high-load aluminium hardware

Height

239 mm - 9 3/8”

Height (rigging included)

278 mm – 11”

Width

909 mm – 35 3/4”

Depth

636 mm – 25”

Weight

38 kg – 83.8 lb

PERFORMANCE SPECIFICATIONS

Frequency Response -10 dB

50 Hz – 20 kHz

Horizontal Dispersion

90°

Vertical Dispersion

Array design dependent

Splay Angles available (Degrees)

from 0° to 7.5° in 0.5° step with additional 0.25° position

Operating con

fi

guration

Quad-amplified

Impedance Low (Nom / Min)

2 x 16 Ω / 2 x 14.4 Ω 

Impedance Midrange (Nom / Min)

16 Ω / 12.6 Ω 

Impedance High (Nom / Min) 

16 Ω / 15.9 Ω 

Watt AES Low (Continuous / Peak)

2 x 450 W / 2 x 1800 W

Watt AES Midrange (Continuous / Peak)

400 W / 1600 W

Watt AES High (Continuous / Peak)

120 W / 480 W

Maximum SPL Output, one box *

143 dB SPL

Maximum SPL Output, four boxes *

155 dB SPL

* calculat

ed using +10 dB C

rest Factor signal @ 1 m, fr

ee field

Summary of Contents for Superfly





























Reviews: