Quick Start
Turning On
Plug into electricity or insert fully charged battery.
Display will automatically load movie and play. (If the unit does not play a movie
automatically, press the power button at the back of the display. RED light
indicates standby mode and GREEN light indicates the unit is switched ON.)
Playing other movies / change content
Connect a USB stick to the unit.
Content from the USB stick will automatically be copied to the unit's internal
memory.
Once the content has copied successfully, the new content will start playing
automatically.
Remove the USB from the unit.
Important: If you no longer require the old content to be played, you will need to
delete the old content (to explain how this is done see Playlist section).
Playing content from SD card
Insert an SD Card to the unit.
The unit will play the content of the SD Card automatically.
Video
Recommended Video Resolution:
Landscape
Format: AVI
Codec: XVID
Audio code: MPEG-1 Audio layer 3 160Kbps
Resolution: 720X400 30PFS 2800Kbps
Portrait
Format: AVI
Codec: XVID
Audio code: MPEG-1 Audio layer 3 160Kbps
Resolution: 400X720 30PFS 2800Kbps
video can be rotated anti-clockwise by 90 degrees
Picture
Recommended Picture Resolution:
Landscape
Format: JPG
Resolution: 600X1024
Portrait
Format: JPG
Resolution: 1024X600
Buttons and Remote Control
Remote Control
On/Off
Turns the unit on/off.
Volume (- / +)
Increase/decrease volume when movies are played.
Menu
Returns the unit to setup mode.
Left
In menu mode, this function is used for moving left through the various
options. In playback mode, this function allows you to go to the previous content
in the playlist.
(Please note: This is only operational for content that is copied from USB or SD
Card, not for content downloaded from i-Display Content Management System.)
Right
In menu mode, this function is used for moving right through the various
options. In playback mode, this function allows you to go to the next content in
the playlist.
(Please note: This is only operational for content that is copied from USB or SD
Card and not for content downloaded from i-Display Content Management
System.)
Up
In menu mode, ths is used for moving up. It is not operational in playback
mode.
Down
In menu mode, this is used for moving down. It is not operational in
playback mode.
Enter
In menu mode, it is used to select an option. It is not operational in
playback mode.
OSD
While playlist is being viewed in
menu mode
and the OSD function is
pressed, a table with Copy/Delete/Sort will appear, enabling the use of these
functions on the playlist content.
(Please note: Playlist refers to only the content that is copied from USB or SD Card
or a playlist viewed from an SD Card and not for content downloaded from
i-Display Content Management System.)
Play/Pause
In playback mode, this function is used to pause or play a specific
JPG or movie. (This function is only operational on content copied from a USB or
SD Card or a playlist viewed from an SD Card and not for content downloaded
from i-Display Content Management System.)
Stop
In playback mode, pressing this function once will stop the current content
playing and will make the screen return to the menu mode. In menu mode, it is
used to go back to main menu.
Slide show
In playback mode, it is used to change between “repeat one” (repeats
the chosen file in endless loop) and “repeat all” (repeats the entire playlist in
endless loop).
(This function is only operational on content copied from a USB or SD Card or a
playlist viewed from an SD Card and not for content downloaded from i-Display
Content Management System.)
Rotate
In playback mode, this is used to rotate JPG pictures. It cannot be used for
movies being played. (This function is only operational on content copied from a
USB or SD Card or a playlist viewed from an SD Card and not for content down-
loaded from i-Display Content Management System.)
Zoom
In playback mode, this is used to zoom on JPG pictures. It cannot be used
for movies played. (This function is only operational on content copied from a USB
or SD Card or a playlist viewed from an SD Card and not for content downloaded
from i-Display Content Management System.)
Mute
In Playback mode, this is used to mute sound. Another click on the Mute
button restores the sound.
Screen Status Indicators
Wi-Fi Signal
Indicates the unit is connected to Wi-Fi network.
Battery Icon
Indicates the unit is working on battery power and shows the
amount of power left in the battery.
Empty Battery Icon
Indicates the battery has 30 minutes of power remaining to
keep the unit activated.
Menu Features
The Menu includes 4 main features:
Playlist / Wi-Fi & Activation to Remote Content Management / Calendar / Settings.
Each can be accessed and activated by either the remote control or buttons on the
side of the unit.
Playlist
The playlist holds a list of content, which can be played on the unit.
To view the playlist:
Select internal memory or SD Card.
Please note: The playlist only shows content copied to internal memory by USB or
SD Card. It
does not
show content downloaded from the i-Display Content
Management System.
Choose any of the selected files that appear on the playlist by moving the up and
down arrows on the remote. Then Click “Enter” to play the relevant content.
(Please note: These files can be either JPEG or various movie formats e.g. MPEG 1, 2
and 4. Recommended format is XVID.)
Click OSD to copy / delete / sort content.
(Please note: This function is only operational on content copied from a USB or SD
Card or a playlist viewed from an SD Card and not for content downloaded from
i-Display Content Management System)
Use the arrows to move between these options and Click “Enter” in order to see the
drop down menu of each of these options as shown below:
Wi-Fi
Holds 3 main features: Wi-Fi list / Wi-Fi Setup / Account Config
Step One: Connect to the internet
Click MENU to see Setting page. Go to the Wi-Fi tab using your remote control (or
the setting buttons on your Player).
Choose the Wi-Fi tab then click OK, select Wi-Fi Setup and click OK.
Click OK on DHCP, the player will automatically locate available Wi-Fi networks.
Click OK on your selected wireless network. (If your Wi-Fi connection does not
require a password the Player will connect to the wireless network automatically.
However, if the wireless network requires a password, click OK, you will need to
fill-in the Username and Password.)
On secure Wi-Fi networks, insert relevant network code using the remote control,
then click “Done”.
Once the unit is connected, a Wi-Fi signal will appear. If an error message appears,
retype your username and password (please ensure you are using the right
information and capital letters if applicable, otherwise the Player will not be able
to connect to the wireless network). If the connection is still not successful, a
problem may have occurred - try rebooting the unit and connect again.
Should you need more support, please go to:
www.i-display.com/config/player_wireless - to download configuration file.
Manual link
Click MENU to see Setting page. Go to the Wi-Fi tab using your remote control (or
the setting buttons on your player).
Choose the Wi-Fi tab and click OK, select Wi-Fi Setup and click OK (see screenshot
above).
From Wi-Fi Setup, go to Manual Link. You will need to insert the relevant
information (see next screenshot). Once this information has been entered, click
Done.
Step Two: Getting an activation code
Make sure the unit is connected to Wi-Fi (Wi-Fi connection via DHCP or Manual
Link explained in Wi-Fi section).
Use the remote control or Player buttons and go to Wi-Fi List in Wi-Fi tab, then click
OK.
Click OK on the i-Display Logo (as shown in screenshot above) and wait for
approximately 3 minutes (the Player will indicate it is connected to Wi-Fi by
showing the Wi-Fi icon) as the Player downloads an "activation slide".
The activation slide downloaded should appear on the Player screen.
Write down the activation code, as it is needed to activate this specific Player on
the i-Display Content Management System.
Step Three: Activate your player within i-Display content management system
Log on to i-Display Content Management System at www.i-display.com
(http://www.i-display.com) and click on the LOGIN link in the home page.
Within the LOGIN page, please fill-in your Username and Password. (If you do not
have a Username and Password, please click CREATE AN ACCOUNT and follow the
instructions. At the end of the registration process you will get a LOGIN access to
i-Display Content Management System.)
Once you are connected to i-Display Content Management System, click on the +
sign button in the Players column to add a Player. Click OK when you see the
“Activate Player” alert.
Enter a Player name (it is highly recommended that the Player name will include a
unique number which you will then be able to use to identify it from other players)
and the unique Activation Code shown on the Player screen, as shown in Step Two:
Getting an activation code.
Set up any applicable Player setting:
(i) Time zone
(ii) Playlist
Then click SAVE to finish.
Now your Player is connected to i-Display Content Management System.
Step Four: Confirm Player is connected
Click MENU to see Setting page. Go to the Wi-Fi tab using your remote control (or
the setting buttons on your Player).
Choose the Wi-Fi tab then click OK. Select Account Config and click OK (Make sure
the Player is connected to Wi-Fi).
The name that appears on the Account Config should be the same as your account
name in i-Display Content Management System (the same account name you gave
when you registered). If the name matches your registered account name, your
Player is now connected to the i-Display Content Management System.
For an introduction on how to use the Content Management System, please select
the Demo tab to get more information.
Calendar
This shows time and date set in unit. If content in internal memory (copied from
USB or SD Card) has a JPG it will appear in a slide show below the digital clock.
To change the date and time on the unit:
Go to the Settings tab by using the arrows to move across the top menu.
(Please note: You must be in the main menu to select the Settings tab).
Use the “Down” arrow to select “Date and Time Setting”.
Press “Enter” to see another sub-menu appear.
Use the “Down” and “Up” arrows to select which options you would like to change,
i.e. year, month, day, hour, etc.
Once option is selected, use the “Left” or “Right” arrows to increase/decrease the
number until reaching the number you desire.
When you have finished selecting the date and time you want, press the “Stop”
button to save your options. This will make the sub-menu disappear.
Then you may return to the previous menu to select another option in “Settings” or
return to another page on the Main Menu.
Settings
Holds a list of functions as shown in the screenshots below e.g. Slideshow
Frequency, Transition effect, etc.:
Slide Show Frequency: Controls the amount of time each JPG will be shown when
played. This only affects content copied from USB or SD Card to internal memory
or content played from SD Card and not content downloaded from i-Display
Content Management System.
Transition Effect: Controls the way each JPG will appear on the screen. This
function does not work for movies. This only affects content copied from USB or
SD Card to internal memory or content played from SD Card and not content
downloaded from i-Display Content Management System.
Date & Time Setting: Controls the time and date which appear in the calendar.
On/Off Schedule: Controls when the unit will turn off and turn on automatically.
Display: Controls brightness and contrast of the unit.
Photo View Options: Allows JPGs to be shown in their original size or fill in the
screen.
Copy Option: Allows reduction of the size of the files copied from USB or SD Card
to internal memory.
Power On Mode: Allows choosing from which location the content will play
automatically when unit is turned on – content on internal memory copied from
USB/SD Card or content downloaded from i-Display Content Management System.
Current default is content on internal memory copied from USB/SD Card.
Default Settings: Return unit to default settings.
Clear Internal Memory: Erases all content copied from USB or SD Card to internal
memory. It does not erase content downloaded from the i-Display Content
Management System.
Firmware Upgrade: Allows upgrading the unit's current firmware.
Upgrading can be done via SD Card: First step is to insert the SD Card with the new
firmware file. Then choose the firmware upgrade function in setting. The unit will
start upgrading the firmware.
Important:
i-Display Content Management System automatically updates the
Player’s firmware as newer versions become available. When you see the following
warning on screen, DO NOT UNPLUG THE POWER, be advised the unit is updating
its firmware. The update process will complete in less than 1 minute and the Player
will automatically reboot and resume normal operation.
Do not turn off the unit while it is upgrading or the unit may malfunction.
Troubleshooting
Why is my media content not up to date?
The Player is probably not connected to the network; please try and reconnect to
Wi-Fi as shown in section Step One: Connect to the internet.
Power Supply Unit Electrical Data
Display:
Input: 12 V, 3000mA
Power Adaptor: Input 100-240V, 50/60 Hz, 0.8A; Output 12V, 3000mA
Produced by:
HONOR ELECTRONIC CO.LTD
Interactive Digital Displays
For further information or support, please contact: [email protected]