Out of the Box Innovations VLXF230 Assembly Manual Download

Page: 2 / 16

THANK YOU!

Welcome and thank you for purchasing the VLXF230. I know you are looking forward to flying a rac

ing drone that can be customized and can deliver efficient air flow, a strong frame, and fantastic flying

capabilities. In this manual you will find the instructions that will take you step by step to complete

your drone and to start flying!

As you are working through the instructions it is important that you READ THE DIRECTIONS! There

are fine points covered that you will miss if you only assemble by the pictures. You will enjoy your

journey much more if you follow the instructions provided in this manual.

As always, we are dedicated to your drone flying experience and if you have thoughts, suggestions,

concerns, or want to share a happy flight, please feel free to contact us!

DISCLAIMER:

Out of the Box Innovations RC can not foresee the equipment you will purchase or how you will use

the product when you receive it. We are not responsible for any injuries or property damage to any

one or anything as it relates to this product. USE AT YOUR OWN RISK!

Summary of Contents for VLXF230










