Otto Bock Juvo Instructions For Use Manual Download

Page: 3 / 124

..............................................................................................................................................................

Product description

............................................................................................................................................

Function

2.1

..............................................................................................................................................

Product overview

2.2

..................................................................................................................................

Safety

..................................................................................................................................................................

Explanation of warning symbols

3.1

............................................................................................................

General safety instructions

3.2

...................................................................................................................

Effects of electromagnetic interference on the product and on the user

3.3

......................................................

Nameplate and warning labels

3.4

..............................................................................................................

Signage on the product

3.4.1

.......................................................................................................................

Nameplate

3.4.2

..........................................................................................................................................

Warning labels

3.4.3

...................................................................................................................................

Delivery

...............................................................................................................................................................

Scope of delivery

4.1

................................................................................................................................

Accessories

4.2

.......................................................................................................................................

Accessories from other manufacturers

4.2.1

...................................................................................................

Storage

4.3

..............................................................................................................................................

Storage during daily use

4.3.1

......................................................................................................................

Storage during extended disuse

4.3.2

............................................................................................................

Preparation for use

...........................................................................................................................................

Safety instructions

5.1

...............................................................................................................................

Initial operation

5.2

...................................................................................................................................

Settings

5.3

.............................................................................................................................................

Changing control unit parameters

5.3.1

.........................................................................................................

Use

......................................................................................................................................................................

Circuit breaker

6.1

...................................................................................................................................

Side panels

6.2

........................................................................................................................................

Removing/installing the side panels

6.2.1

.......................................................................................................

Adjusting the side panels

6.2.2

.....................................................................................................................

Adjusting the control panel position

6.2.3

.......................................................................................................

Legrests

6.3

............................................................................................................................................

Removing/installing the legrests

6.3.1

............................................................................................................

Adjusting the legrests

6.3.2

..........................................................................................................................

Backrest

6.4

............................................................................................................................................

Folding the backrest up/down

6.4.1

..............................................................................................................

Adjusting the Back Angle

6.4.2

.....................................................................................................................

Getting in and transferring

6.5

...................................................................................................................

Control unit

6.6

........................................................................................................................................

VR2 control unit

6.6.1

..................................................................................................................................

Control panel

6.6.1.1

.....................................................................................................................................

Buttons and display functions

6.6.1.1.1

...............................................................................................................

Control panel

6.6.1.2

.....................................................................................................................................

Buttons and display functions

6.6.1.2.1

...............................................................................................................

R-Net control unit

6.6.2

................................................................................................................................

TEN° control panel

6.6.2.1

..............................................................................................................................

Buttons and display functions

6.6.2.2

...............................................................................................................

Adjustment possibilities

6.6.2.3

.......................................................................................................................

Environmental control via Bluetooth

6.6.2.4

.......................................................................................................

Activating devices

6.6.2.4.1

...............................................................................................................................

Pairing

6.6.2.4.2

...............................................................................................................................................

Selecting the connected devices

6.6.2.4.3

...........................................................................................................

Deactivating devices

6.6.2.4.4

............................................................................................................................

Operating mouse functions on a PC

6.6.2.4.5

......................................................................................................

Table of contents

Juvo

Table of contents

Summary of Contents for Juvo





























































































































Search results

Summary of Contents for Juvo

Reviews:

Related manuals for Juvo

Brands by name

Popular brands

Otto Bock Juvo, Instructions For Use Manual

Search results

Summary of Contents for Juvo

Reviews:

Related manuals for Juvo

Brands by name

Popular brands