Otto Bock B500 plus Instructions For Use Manual Download Page 15

Ottobock  |  15

B500 plus

Preparation for Use

Closing the battery tray (on models without drive wheel
suspension)

1)  Place the cover on the battery tray.
2)  Close the strap.
3)  Replace the seat bottom and push it down tightly.
4)  Press  the  seat  cushion  firmly  on  to  the  hook-and-loop

material on the seat surface.

5.2.4 Charging the battery

See  the  power  wheelchair  instructions  for  use  (user)  for  all
information regarding the charging process.

5.2.4.1 Battery charging information

The range of the power wheelchair is determined by the bat­
tery  capacity.  The  battery  capacity  is  influenced  by  many
factors. In addition to the temperature, battery age and driv­
ing  conditions,  the  charging  cycle  also  has  a  pronounced
effect on the capacity and therefore on the range.
Batteries  reach  their  full  capacity  only  after 

20  -  30

  charge

cycles.  Only  if  the  full  capacity  of  the  batteries  has  been
reached can the power wheelchair achieve the stated range. 
At  temperatures  of 

<  0 °C/32 °F

  the  battery  capacity  drops

by up to 

35%

 in relation to the capacity for an outside tem­

perature  of 

20 °C/68 °F

.  This  shortens  the  range  of  the

power  wheelchair  accordingly.  Moreover  the  charge  level
displayed  on  the  control  panel  can  differ  more  significantly
from the actual battery capacity.
The following information should be observed for an optimal
charging cycle:

The batteries can be charged at any time, regardless of
the remaining battery capacity.

It takes about 

10 hours

 until a discharged battery (only

1  flashing  segment)  is  completely  charged.  When  the
charging  process  is  complete,  the  battery  charger  can
remain  connected  to  the  power  wheelchair  with  no  risk
of  overcharging  or  damaging  the  battery.  The  battery
charger  features  a  programmed  recharging  phase  that
will  maintain  the  battery  capacity  at  the  level  that  has
been reached.

If  the  power  wheelchair  is  used  every  day,  the  battery
should be charged every night.

Never  discharge  the  batteries  completely  (deep  dis­
charge). 

The  batteries  will  gradually  discharge  if  the  wheelchair
is  not  used  for  extended  periods  of  time.  If  the  power
wheelchair is not used for an extended period, the bat­
teries should be charged 

1 x per week

 to maintain their

capacity.

The  fuse  should  be  removed  if  the  wheelchair  is  not
used for more than 3 days.

The power wheelchair control unit must be switched off
while the batteries are charging to allow all of the char­
ging current to be fed into the battery.

Summary of Contents for B500 plus





























Reviews: