manualshive.com logo in svg

Ostermann e-Desk 1+2, Design And Operating Instructions

Share
Download
Ostermann e-Desk 1+2 Design And Operating Instructions Download Page 9

www.ostermann.eu

9

8. Setting the upper and lower limits

This product has been designed to give you the widest possible range of positions with the lowest and highest settings. If you 

do not want to use them, change the settings individually in the following steps:

Make sure that the power is on and a number is displayed in the LED display (if no number is displayed, please follow the reset 

procedure in the „Use“ section).

Set the highest position:

Use the Up/Down key to move the frame to the desired maximum position. Keep the „M“ key pressed until „S“ flashes once 
in the LED display and then release the key. Then press the key twice in quick succession. The LED display changes to „999“ 

when the key is pressed for the third time and then automatically returns to the selected height. The highest position is set.

Fix lowest position:

Use the Up/Down key to move the table frame to the desired lowest position. Keep the „M“ key pressed until „S“ flashes once 

in the LED display and then release the key. Then press the key twice in quick succession. The LED display changes to „000“ 
when the key is pressed for the third time and then automatically returns to the selected height. The lowest position is set.

To remove the position settings: 

Use the Up/Down key to move the table to a new position. Keep the „M“ key pressed. As soon as the LED display flashes „S“ 
once, release the key. Then press the „M“ key again until the display changes to „555“ (ignore interim results). Release the key. 
After a few seconds, the display automatically returns to the numbered height position. The upper and lower limits have now 
been removed.

During the reset procedure, the table frame is completely retracted. Make sure that there are no objects under the desk. 

If the settings of the lowest and highest positions are set again, it is possible that the set positions 1, 2, 3 or 4 can no longer 
be approached. If this happens, readjust the position.

If you intend to change the lowest and highest position which is outside your position setting, a new reset is necessary.

Summary of Contents for e-Desk 1+2











Reviews:

No comments

Brands by name

Popular brands

Load more brands