5.
Place threaded jar nut or threaded jar skirt over
blade and jar (Note: If there are slots on top of
collar, line them up with notches on jar.) Place the
threaded jar nut or threaded jar skirt on jar and turn
it clockwise to tighten. (Figure 4)
6. Place jar assembly onto base. (Figure 5)
7.
Line up tabs of jar with tabs on blender base.
Make sure the tab of the jar on the left side is in the
back of the tab of the blender base and the tab of
the jar on the right side is in front of the tab of the
blender base. Make sure jar is seated into position.
(Figure 6)
8. Place ingredients into jar.
9. Place lid with feeder cap on jar.
10. Plug the power cord into a 120 Volt
AC electrical outlet.
11. Slide switch to HIGH or LOW. (If your model does
not have a slide switch, push HIGH or LOW button.)
12. Push desired speed and blend ingredients
to desired consistency.
13. Press OFF to stop the blender.
14. To use PULSE, select HIGH or LOW. Push PULSE
and hold down for desired length of time. Release
PULSE and allow blade to stop. Repeat cycle as
desired.
Blending Tips
• Put liquids in the jar first, unless a recipe says otherwise.
• Crushing ice: Crush 6 ice cubes or approximately 2 cups
of ice at a time.
• Do not remove the lid while in use. Remove filler cap to
add smaller ingredients. (Figure 7)
• Cut all firm fruits and vegetables, cooked meats, fish and
seafood into pieces no larger than 3/4 inch (1.8 cm) to
1 inch (2.5 cm). Cut all kinds of cheeses into pieces no
larger than 3/4 inch (1.8 cm).
• This blender will not mash potatoes, whip egg whites or
substitute dairy toppings, mix stiff dough or grind raw
meat.
Hot Foods
• Open the Filler Cap to vent steam. Tilt Filler Cap away from you.
Keep hands away from the cover opening to prevent possible burns.
• When working with hot liquids, remove Filler Cap and start blending at
a low speed. Then move to a faster speed. DO NOT add liquid over the 4 cup
(1 liter) level.
5
4
Using Your Blender
1.
Clean blender according to the instructions in the “Cleaning and Storing
Your Blender” section.
2. Turn jar upside down so the small opening is at the top. (Figure 1)
3. Place sealing ring over jar opening. (Figure 2)
4. Place blade into jar. (Figure 3)
1
2
3
4
5
6
7
8
9
10 11 12
EASY CLEAN
PURÉE
CREAM
CHOP
WHIP
MIX
GRATE
BLEND
SHRED
GRIND
LIQUEFY ICE CRUSH
LOW
HIGH
16-Speed
LOW
HIGH
1
2
3
4
5
6
7
8
9
10 11 12 13
14
EASY CLEAN
BEAT
PURÉE
CREAM
CHOP
WHIP
MIX
MINCE
GRATE
BLEND
SHRED
GRIND
LIQUEFY
ICE CRUSH
14-Speed
LOW
HIGH
12-Speed
LOW
HIGH
1
2
3
4
5
6
7
8
9
10
EASY CLEAN
PURÉE
CHOP
WHIP
MIX
GRATE
BLEND
GRIND
LIQUEFY ICE CRUSH
10-Speed
LOW
HIGH
1
2
3
4
5
6
7
8
PURÉE
CHOP
MIX
PULSE
LIQUEFY
SHAKE
SMOOTHIE
ICE CRUSH
8-Speed
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
PULSE EASY CLEAN
STIR
BEAT
PURÉE
CHOP
WHIP
MIX
ICE CRUSH
GRATE
BLEND
SHRED
GRIND
MASH
LIQUEFY
FRAPPÉ
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
