7
CARE AND CLEANING
Make sure the unit is switched off and unplugged from the mains supply socket before cleaning. The blades are
very sharp, take care when washing them. Do not immerse the motor unit, power cord or plug in water or any other
liquid.
Cleaning the blending jug
1. Half fill the blending jug with warm water and add two drops of detergent. Fit the lid and stopper.
2. Set the speed control to low and gradually increase to high. Allow your blender to run for 30-60 seconds then turn the
speed control to the position.
3. Remove the blending jug from the motor base. Wipe down the outside of the blending jug using a damp cloth or
sponge then rinse it under running water. Allow it to dry thoroughly.
Cleaning the lid, stopper and motor base
• Wash the lid and stopper in warm, soapy water. Rinse and dry thoroughly.
• Wipe down the motor base using a damp cloth or sponge and dry thoroughly. Make sure you only use a mild detergent
solution.
• Do not wash the blending jug, lid or stopper in a dishwasher.
Storing
After cleaning, store your blender with the lid loosely fitted to allow air to circulate and prevent odours from developing. The
power cord can be stored underneath the base (fig. 3).
TROUBLESHOOTING
If your blender does not turn on:
1. Turn the speed control to the position and unplug your blender from the electrical outlet.
2. Remove the blending jug from the base and make sure the blade is free from any obstruction.
3. Plug the unit back in.
4. Make sure the blending jug is securely placed on the motor unit.
5. Restart the unit by turning the speed control to the desired setting.
If your blender stops during operation:
The motor is designed to protect itself from overheating and if this happens, the overload protection device will be activated
and the motor will turn itself off. To reset the motor:
1. Turn the speed control to the position and unplug your blender from the electrical outlet.
2. Remove the blending jug from the base and make sure the blade is free from any obstruction.
3. Wait 30-45 minutes for the unit to cool.
4. Press the resettable fuse button located underneath the base (fig. 4).
5. To restart your blender, turn the speed control to the position and plug your blender into the electrical outlet.
6. Make sure the blending jug is securely placed on the motor unit.
7. Restart unit by turning the speed control to the desired setting.
If your blender will still not operate, it has not cooled sufficiently. Turn the speed control to the position and wait another
10-20 minutes before trying again.
Summary of Contents for OBL104X
