7
6
MEASURING CHART FOR BLENDING CUP
MILLILITERS
CUPS
OUNCES
50
.21
1.70
100
.42
3.40
150
.63
5.00
200
.85
6.76
250
1.10
8.50
300
1.25
10.00
350
1.50
12.00
400
1.70
13.50
450
1.90
15.25
500
2.10
17.00
550
2.32
18.50
600
2.50
20.25
650
2.75
22.00
700
3.00
24.00
REMOVAL OF BLENDER SHAFT
Grasp blender shaft firmly and rotate Motor Housing from lock ( ) to unlock ( ) position to unlock.
The chopper accessory is ideal for chopping a wide range of vegetables, dried fruits, nuts, etc.
1. Using Chopping Blade:
• Insert Chopping Blade into the Chopping Bowl
• For best results, cut large ingredients into pieces of approximately 15mm cubed before
chopping, Add certain amount of purified water to facilitate smooth chopping. The amount of
ingredients should not exceed the maximum capacity of the chopping bowl.
NOTE: Do not chop large ice cubes or extremely hard foods, such as whole nutmegs, coffee
beans, dried corn and grains.
• Secure the Chopper cover by setting on the Bowl , make sure the 2 tubers on the cover
aligned with the 2 grooves of the chopping bowl, push down the cover to lock in place
(see below illustrations). The upper shaft of the Chopping Blade will fit into the receiving hole
in the underside of the Cover.
• Attach the Motor Housing into the opening of the Bowl cover and turning the Motor Housing
from unlock ( ) to lock ( ) position until the Motor Housing is firmly locked into place. Plug
cord into convenient outlet.
• The chopper has two speeds. Press and hold the appropriate button to switch the Hand
Blender on. Release the button to switch the unit off.
USING THE CHOPPER ATTACHMENT
• Use the Low speed where possible especially if
you want to chop the food into bigger pieces. The
TURBO speed can be used for chopping the food
to small pieces or for pureed foods.
• When Low speed is selected, adjust the Speed
Control Dial on top of the motor housing for more
precise speed.
• During chopping process, you can insert food
through the Feeding Tube and use the Food
Pusher to press food into the bowl if necessary.
• If the ingredients stick to the Chopper Bowl
sides, loosen them by adding a small amount of
liquid or by using a spatula to scrape the food
back into the inner part of the Bowl.
• Release the Button and allow the blade to come
to a complete stop before removing the Motor
Housing by turning clockwise to unlock from the
Bowl Cover. Take care when removing the Blade
and hold only by the shaft handle as the metal
blade is sharp.
• Remove the Bowl Cover by pulling out the 2
fasteners together and lift up the bowl cover.
NOTE: Do not clean blades with fingers but use
a spoon or spatula to scrape food into Bowl after
Blade is removed.
2. Using Slicing/Shredding Disc:
• There is a Slicing/Shredding Disc
enclosed with the appliance for additional
food processing. Select the desired disc
(shredding side for strips and slicing side
for slices), assemble the disc onto disc
shaft with the selected disc side facing
up.
• Follow the above steps to secure the
Chopper Cover on the Chopping Bowl
and lock in place. Attach the Motor
Housing into the opening of the Bowl
cover and lock in place.
• Operate the Chopper as per the above
instructions. Stop and wait for the slicing/
shredding disc to stop before removing
the bowl cover. Always use the Food
Pusher to yield more evenly sliced/
shredded food.
Hints:
CAUTION: The chopping blade and
slicing/shredding disc are extremely
sharp. Use with caution when handling
or storing.
Tuber
Fastener
Groove
Speed control dial
Power/Low speed button
High speed button (TURBO)
Feeding tube
Bowl cover
Food pusher
Chopping blade
Chopping bowl
Speed control dial
Power/Low speed button
High speed button (TURBO)
Food pusher
Disc shaft
Chopping bowl
Slicing: Slicing Disc
facing up
Feeding tube
Bowl cover
Shredding: Shredding disc facing up
FPSTHB2620-049_15EM1.indd 6-7
8/7/15 11:28 AM
