OSS OSS-521 Gen4 Installation Manual Download Page 4

Page: 4 / 38

One Stop Systems

OSS-521 Gen4 BP

Getting Started

This is section is all about the steps on how to install the backplane. You will find instructions for the following procedures:



Unpacking



Description of Parts



Hardware Requirements



Backplane Installation



Cable Adapter Card Installation



Link Cable Installation



Powering Up the unit / system



Board LED Indicator



Verify Device Installation

Unpacking

Check and identify the standard supplied item. Inspect the backplane for physical defects and damages.



To achieve good performance and reliability it is recommended to use a certified and compatible set of an OSS Gen4
adapter cards (aka: Host Interface Board) and a Gen4 Mini-SAS

HD SFF

8644 c

ables.



The OSS backplane is designed and programmed to work with OSS Gen4 adapter cards.

Summary of Contents for OSS-521 Gen4







































Search results

Summary of Contents for OSS-521 Gen4

Reviews:

Related manuals for OSS-521 Gen4

Brands by name

Popular brands

OSS OSS-521 Gen4, Installation Manual

Search results

Summary of Contents for OSS-521 Gen4

Reviews:

Related manuals for OSS-521 Gen4

Brands by name

Popular brands