manualshive.com logo in svg

Ositech comm 28800, User'S Manual And Reference

Share
Download
Ositech comm 28800 User'S Manual And Reference Download Page 2

ii

Copyright

Information in this document is subject to change without notice.

Copyright 1996-1997 by Ositech Communications Inc., Guelph,
Ontario, Canada.

Ositech Communications Inc. shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this
material.

Trumpcard is a trademark of Ositech Communications Inc.

P/N: 614005-001 Revision 3.0

How To Contact Us

At Ositech Communications, we make every effort to provide our
customers with products that fit their needs and work well. If you wish to
communicate with technical support, sales, or any other department at
Ositech, please contact us in one or more of the following ways:

Ositech Communications Inc.
679 Southgate Drive
Guelph, Ontario, Canada
N1G 4S2

Toll Free Telephone:

1-888-OSITECH  (1-888-674-8324)

Local Telephone:

(519) 836-8063

Facsimile:

(519) 836-6156

24 HR Bulletin Board Service
(519) 836-1196
[8-N-1, up to 33.6 KBPS]

Internet:

World Wide Web

http://www.ositech.com

FTP

ftp.ositech.com

E-Mail

[email protected]
[email protected]

Summary of Contents for 28800























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands