background image

Page 31

Installation and Operation Manual - Osburn 1700-I

ENGLISH

To determine the need to add floor protection

 (D)

 beyond the hearth extension

 (A)

, the following 

calculation must be done using the data in 

«Table 4 : Data for Floor Protection Calculation»

 o

this section: D = B - G, where G = A-C. 

HEARTH SLAB:

NON-COMBUSTIBLE MATERIAL

FLOOR PROTECTOR:

NON-COMBUSTIBLE MATERIAL

  B

  C

  D

  E

F

  A

  G

HEARTH SLAB:

NON-COMBUSTIBLE MATERIAL

FLOOR PROTECTOR:

NON-COMBUSTIBLE MATERIAL

  B

  C

  D

  E

F

  A

  G

Figure 22: Additional Floor Protection - Raised Installation

Figure 23: Additional Floor Protection - Not Raised Installation

Table 4 : Data for Floor Protection Calculation

A

B

C

D

E

Air Jacket

Maximum 
Extended

Dimension 

of the hearth 

extension

See section 

9.2.1 and 

9.2.2

(93 mm)

G = (A-C) 

D=B- G

(181 mm)

Back from 

fireplace 

facing 1 

"

Minimum 
Extended

Dimension 

of the hearth 

extension

See section 

9.2.1 and 

9.2.2

¼

(57 mm)

G = (A-C) 

D=B- G

8 ½" 

(216 mm)

Back from 

fireplace 

facing 2 

¾

"

If the value 

(D)

 is negative or zero, additional floor protection in front of the unit is not needed 

because the masonry fireplace hearth extension is long enough. If the value 

(D)

 is positive, an 

additional floor protection in front of the hearth extension at least equivalent to the result 

(D)

 

must be added.

9.2.1  Installation Raised of 4" (102 mm) and Less

If non-combustible material floor protection needs to be added in front of and level with the 
hearth extension of the masonry fireplace (F = 4" [102 mm) or less), an R-value equal to or 
greater than 1.00 is required and should extend at least 22" (559 mm) in front of the unit 

(B)

Refer to

 «Figure 23: Additional Floor Protection - Not Raised Installation»

9.2.2  Installation Raised of More Than 4" (102 mm)

If the extension of the masonry hearth is raised at least 4" (102 mm) from the floor protection, a non-
combustible material, without an R-value, must extend at least 16" (406 mm in USA) or 18" (457 mm  
in Canada) in front of the unit 

(B)

. Refer to 

«Figure 22: Additional Floor Protection - Raised Installation»

.

Summary of Contents for 1700-I

























































Reviews: