2
SAFETY INSTRUCTIONS
Osaki Power Tools are committed to the Production of Quality Power Tools
that are designed for high performance and long service life.
If safety and maintenance procedures are observed they will last for many years.
Man, Earth and the Universe
are forces that create an
immovable centre of balance . . .
the
balance of power
“
”
7
PARTS BREAKDOWN
No.
Description
Order Code
OSA-298
1
QUICK CHANGE COLLET
NUT
KIT
-1
101S
2
COLLET
NUT
-1
102S
3
FINGER
REST
-1
103S
4
BEARING 698-2Z
-1
104S
5
SCREW NAIL
-1
105S
6
FIELD COIL
(ST
A
T
OR)
-1
106S
7
ARMA
TURE
-1
107S
8
CARBON BRUSH SET
-1
108S
9
BEARING 626-2Z
-1
109S
1
0
CIRCUIT
BOARD SET
-1
110S
11
ON-OFF SWITCH SET
-1
111
S
1
2
SCREW NAIL
-1
112S
1
3
WIRE GRIP
BLOCK
-1
113S
1
4
ELECTRIC WIRE
-1
114S
1
5
WIRE COVER
-1
115S
1
6
SHAFT
LOCK BUTT
ON
-1
116S
1
7
SPRING
-1
117S
1
8
SHAFT
LOCK PIN
-1
118S
1
9
SHELL
SET
-1
119S
2
0
RING
-1
120S
2
1
V
ARIABLE SPEED CONTROL
-1
121S
2
2
COLLET
S
P
ANNER
280-1607T
GENERAL SAFETY
l
Keep work area clean - clutter invites injury.
l
Store tool in a dry, secure place, away from
children.
l
Always keep the cord away from moving parts
of the tool.
l
Always wear safety glasses and a dust mask if
necessary.
l
Before using the tool ensure that all parts are
functional. A damaged part should be repaired
and serviced by an authorised technician.
l
Ensure work area is well lit.
l
Disconnect the tool from the power source when
not in use.
l
Stay alert at all times. Watch what you are
doing and use your common sense. Do not
operate tools when you are tired.
l
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect
the plug.
l
Only use original Osaki accessories which can
be obtained from your Osaki dealer.
l
Ensure that the collet size corresponds with
the shaft size of the accessory.
l
Compare the maximum allowed rpm of each
accessory with that of the tool.
l
Do not expose power tools to rain or damp
conditions.
l
Do not store the machine in locations where
the temperature may reach or exceed 50
o
C
(122
o
F).
l
Do not use power tools near flammable liquids
or gases.
l
Do not let people who are not familiar with
power tools handle them without supervision.
l
Use the correct tool for the job, do not force
small tools or attachments to do the job of a
heavy tool. The job will be done more
efficiently and safely if the tool is used at the
intended rate.
l
Never apply force.
l
Do not try to stop the accessory rotating with
your hand. Wait for it to stop.
l
Never press the shaft lock while the tool is
running.
l
Do not use grinding wheels over 1
1/4
”
(32mm)
diameter
.
l
Do not use drill bits over
1/8
” (3.2mm)
diameter.
SPECIFICATIONS
Model Number
MT32E
Nominal Voltage
230v~50 Hz
Power Consumption
120W
No Load Speed Speed
8,000-30,000rpm
Noise
82db(A)
Weight
640gms
Complies to EN 50144-1 & EN 68 1977.
Press OSA-279-8500K Manual.qxd 21/03/02 14:47 Page 2