manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Operator'S Manual, Page: 54 / 62

Share
Download
Orthman 125-087-02-EN-OM Operator'S Manual Download Page 54

MAINTENANCE AND SPECIFICATIONS

DR12x2 Row Hopper Planter OM-EN 

7-6

Hydraulic Component Air Bleed 

Procedure

This procedure is required after replacement of hydraulic 
component or if hydraulic oil has been drained from the 
hydraulic system.

WARNING

!

Prevent hydraulic system damage. Perform the 
hydraulic component air bleed procedure correctly. 
Failure to follow this procedure could cause hydraulic 
system damage.

1. Park implement on a clean, level surface.
2. Unfold wings and lower implement to the ground.

DANGER

!

Use an appropriate lifting device to support left and 
right wing fold cylinders. Failure to follow this 
information could result in death or serious injury.

3. Use an appropriate lifting device to support left wing 

fold cylinder (1).

4. Remove cotter pin and pin on rod end of left wing fold 

cylinder. See “Wing Fold Cylinder Removal” on 
page 7-5.

5. Position and support left wing fold cylinder with a 

block of wood (2) as shown in Figure 7-4.

6. Repeat steps 3–5 for right wing fold cylinder.

ORM000149

Figure 7-4: Left Wing Fold Cylinder

7. Check hydraulic oil level in tractor and add oil as 

necessary.

8. Start tractor and run at 1800 revolutions per minute 

(RPM).

NOTE: 

If performing hydraulic component air bleed 

procedure on machines running different than 
1800 rpm, bleed rate times must be adjusted to a 
113 liters per min (LPM), or 30 gallons per min 
(GPM).

DANGER

!

High-pressure fluid can penetrate eyes and skin. 
Relieve pressure on hydraulic system before servicing 
or disconnecting hoses. Wear proper hand and eye 
protection. When searching for leaks, use cardboard or 
wood instead of hands.

9. Check for leaks.
10. Fully extend and retract left and right wing fold 

cylinders at least two times, maintaining hydraulic 
pressure at full extension for at least 30 seconds.

11. Extend cylinders one more time, maintaining 

hydraulic pressure at full extension for 1 minute.

12. Check for leaks.
13. Check hydraulic oil level in tractor and add oil as 

necessary.

14. Install cotter pin and pin on rod end of left and right 

wing fold cylinders.

1) Left wing fold cylinder

2) Block of wood

2

1

Summary of Contents for 125-087-02-EN-OM































































Reviews:

No comments