Orthman 125-087-02-EN-OM Operator'S Manual Download Page 53

Page: 53 / 62

MAINTENANCE AND SPECIFICATIONS

DR12x2 Row Hopper Planter OM-EN

7-5

Wing Fold Cylinder Removal

NOTE:

Left wing fold cylinder removal procedure shown.

Right wing fold cylinder removal procedure is
similar.

1. Park implement on a clean, level surface.
2. Unfold wings and lower implement to the ground.

DANGER

Avoid high-pressure fluid hazards. Relieve hydraulic
pressure before servicing or disconnecting hoses.
Failure to follow this information could result in death or
serious injury.

3. Relieve hydraulic system pressure.
4. Install identification tags and disconnect two

hydraulic hoses (1) from wing fold cylinder (2). Close
all openings using caps and plugs.

DANGER

Use an appropriate lifting device to support and lift wing
fold cylinder. Failure to follow this information could
result in death or serious injury.

5. Use an appropriate lifting device to support wing fold

cylinder.

6. Remove two cotter pins (3), two pins (4), and wing

fold cylinder.

ORM000148

Figure 7-3

7. Clean and inspect parts. Repair or replace as

necessary.

8. Installation is done in reverse order of removal.
• Bleed wing fold cylinder. See “Hydraulic Component

Air Bleed Procedure” on page 7-6.

1) Hydraulic hose (2 used)

3) Cotter pin (4 used)

2) Wing fold cylinder

4) Pin (2 used)

Summary of Contents for 125-087-02-EN-OM































































Search results

Summary of Contents for 125-087-02-EN-OM

Reviews:

Orthman 125-087-02-EN-OM, Operator'S Manual, Page: 53 / 62

Search results

Summary of Contents for 125-087-02-EN-OM

Reviews: