manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Operator'S Manual, Page: 36 / 62

Share
Download
Orthman 125-087-02-EN-OM Operator'S Manual Download Page 36

PREPARATION AND SETUP

DR12x2 Row Hopper Planter OM-EN 

4-12

Preparation for Planter Transport

1. See “Safe Transport” on page 2-5 for safe operation 

of tractor during transport.

2. Place the planter in the raised position with the wings 

folded. See “Wing Fold” on page 4-7.

3. Do not attempt to transport the machine fully loaded. 

NOTE: 

Seed load must be at half capacity before 

machine is transported.

4. Enable tractor safety lights. See “Warning and Safety 

Lights” on page 2-6.

5. Do not exceed 20 mph (32 kph) when transporting 

the planter.

Preparation for Planter Operation

1. Inspect implement for worn or damaged parts. See 

“Implement Inspection” on page 7-7.

2. Be sure all mechanical, hydraulic, and electronic 

connections are in place and free of making contact 
with other moving parts. 

3. Make sure cab hydraulic control configuration is 

easily accessible and set to the preference of the 
primary operator.

4. Make sure tractor is adequately ballasted for safe 

operation. See the tractor operator’s manual for more 
information on proper ballasting instructions.

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Do not stand between 
the tractor and implement when connecting or 
disconnecting the implement.

5. Connect implement to tractor. See 

“Implement-to-Tractor Connection” on page 4-4.

6. Raise bar stands (1) to highest point and install stay 

pins (2).

ORM000123

Figure 4-21

7. Review the toolbar settings and features in 

Chapter 5, “Operation and Field Settings”

. Make 

any necessary adjustments. 

1) Bar stand (2 used)

2) Stay pin (2 used)

2

1

Summary of Contents for 125-087-02-EN-OM































































Reviews:

No comments