
PREPARATION AND SETUP
DR12x2 Row Hopper Planter OM-EN
4-4
Implement-to-Tractor
Connection
The DR12x2 Row Hopper Planter features a dual-mount
hitch to dictate whether using twin row or single row
operation. As part of the unique dual-mount hitch, the
hitch top link has two mounting locations for the tractor
3-point hitch. For more information, see “Hitch Pin
Position” on page 4-11.
See the tractor operator’s manual for more information
on properly connecting the implement.
The tractor’s hydraulic system must be able to support
3000 psi (207 bar) of working pressure, and have a
minimum 2250 psi (155 bar). The hydraulic system
capacity should be 2 gal (7.5 L) minimum.
DANGER
!
Avoid crushing. Failure to follow this information will
result in death or serious injury. Make sure all personnel
are clear of the implement before lowering.
DANGER
!
Avoid crushing. Failure to follow this information will
result in death or serious injury. Do not stand between
the tractor and implement when connecting or
disconnecting the implement.
1. Back up tractor to the implement hitch. Place the
tractor in park, turn off the engine, and remove the
key before connecting the implement. Injury or death
can result from being trapped between the tractor
and implement.
2. Set tractor’s three-point hitch lift links. Hitch lift links
should be adjusted to the operating depth
dimensions indicated in the tractor operator’s
manual.
3. Set tractor’s three-point hitch lateral float pins.
Lateral float pins should be placed in the lower holes
to allow machine to “float” and follow the ground
surface.
4. Set tractor’s three-point hitch sway blocks. Sway
blocks and bumpers should be installed if no
implement guidance is being utilized with machine.
5. Connect the tractor’s lower three-point hitch points
(1) to the lower hitch tug pins (2) on the implement.
6. Adjust the tractor’s upper three-point hitch point (3)
as necessary to connect the hitch point to the upper
hitch pin (4) on the implement.
ORM000126
Figure 4-2: Single Row Planting Hitch Pin Position
NOTE:
Single row planting hitch position is shown. For
twin row planting hitch position, see “Hitch Pin
Position” on page 4-11.
DANGER
!
Avoid high-pressure fluid hazards. Failure to follow this
information will result in death or serious injury. Relieve
hydraulic pressure before servicing or disconnecting
hoses.
7. Relieve hydraulic system pressure before connecting
the tractor. Attach hydraulic hoses to the tractor
according to the operator preferences.
8. Attach toolbar controller electrical connections and
toolbar safety lights to the tractor.
9. Make sure all electrical and hydraulic lines are
plumbed over the hitch to the tractor to avoid wear or
damage.
10. Raise bar stands to highest point and install stay
pins.
1) Lower three-point hitch
point (2 used)
3) Upper three-point hitch
point
2) Hitch tug pin (2 used)
4) Hitch Pin
3
2
1
1
2
4
Summary of Contents for 125-087-02-EN-OM
