
OR-CR-255
(ENG) Manual
Presence sensor
ORNO-LOGISTIC Sp. z o.o.
ul. Rolników 437
44-141 Gliwice
tel. 32 43 43 110
(ENG) IMPORTANT!
Before using the device, read this Service Manual and keep it for future use. Any repair or modification carried out by yourselves results in loss of guarantee. The
manufacturer is not responsible for any damage that can result from improper device installation or operation.
While installing the device, remember that the sensor is activated by the detected motion or heat. To avoid false alarms, place the sensor in location not exposed to
direct sunlight and far from heat sources such as radiators, heaters, light bulbs, etc.
In view of the fact that the technical data are subject to continuous modifications, the manufacturer reserves a right to make changes to the product characteristics and
to introduce different constructional solutions without deterioration of the product parameters or functional quality.
The latest version of the Manual can be downloaded from www.orno.pl. Any translation/interpretation rights and copyright are reserved in relation to this Manual.
1.
Do not use the device against its intended use.
2.
Disconnect the power supply before any activities on the product.
3.
Do not dip the device in water or another fluids.
4.
Do not operate the device when its housing is damaged.
5.
Do not open the device and do not repair it by yourselves.
Each household is a user of electrical and electronic equipment, and hence a potential producer of hazardous waste for humans and the environment, due to the presence of
hazardous substances, mixtures and components in the equipment. On the other hand, used equipment is valuable material from which we can recover raw materials such as
copper, tin, glass, iron and others. The weee sign placed on the equipment, packaging or documents attached to it indicates the need for selective collection of waste electrical
and electronic equipment. Products so marked, under penalty of fine, cannot be thrown into ordinary garbage along with other waste. The marking means at the same time that
the equipment was placed on the market after August 13, 2005. It is the responsibility of the user to hand the used equipment to a designated collection point for proper processing.
Used equipment can also be handed over to the seller, if one buys a new product in an amount not greater than the new purchased equipment of the same type. Information on
the available collection system of waste electrical equipment can be found in the information desk of the store and in the municipal office or district office. Proper handling of used
equipment prevents negative consequences for the environment and human health!
08/2018
TECHNICAL SPECIFICATION
DESCRIPTION
Power source:
Rated Load: Max:
Detection Range:
Adjustable daylight sensor:
Adjustable hold time:
Detection range:
Power Consumption:
Detection Motion Speed:
Temperature:
Installation Height:
Protection level
Dimmension:
Net weight:
230V~, 50 Hz
2000W
360°
<3 – 2000 lux
min: 10 sek. ± 3 sek.
max: 30min. ± 2 min.
max. Ø20m.
0.45W (praca); 0.1W (czuwanie)
0,6~1,5 m/s
-20
0
C~+40
0
C
2 – 2,6 m
IP65
102,5 x 102,5 x 58,3 mm
0,14 kg
The product is a new saving-energy switch; it adopts good sensitivity
detector, integrated circuit. It gathers automatism, convenience, safety,
saving-energy and practicality functions. The wide detection field is
consisting of detectors. It works by receiving human motion infrared
rays. When one enters the detection field, it can start the load at once
and identify automatically day and night; its installation is very
convenient and its using is very wide
FUNCTION
Can identify day and night: The consumer can adjust working state in different ambient light. It can work in the daytime and at night when it is
adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX, when it is adjusted on the “moon” position (min). As for the
adjustment pattern, please refer to the testing pattern.
Time-Delay is added continually: When it receives the second induction signals within the first induction period, it will compute time once more on
the basic of the first time-delay rest (Set time).
Time–Delay is adjustable. It can be set according to the consumer’s desire. The minimum time is 10sec±3sec. The maximum is 30min±2min.
INSTALLATION/ CONNECTION-WIRE DIAGRAM
rys. 1a Instalation
rys. 1b Connection diagram