2
IM0973142 R1-4
IM0973142 R1-4
3
CORRECT
INCORRECT
INCORRECT
U-Bolt of all clips on
dead end of rope
Staggered clips
U-Bolt of all clips on
live end of rope
Installation Manual
Camera PTZ PAL/NTSC Alu/SSt
Article no. 0506911; Camera PTZ PAL Sst
Article no. 0516911; Camera PTZ PAL Sst RS485
Article no. 0506952; Camera PTZ PAL Alu
Article no. 0516951; Camera PTZ PAL Alu RS485
Article no. 0506961; Camera PTZ NTSC Alu
Article no. 0516961; Camera PTZ NTSC Alu RS485
Safety
In order to guarantee safe operation, these safety instruc-
tions must be read before you start using this equipment.
• Do not open the enclosure. The camera and the P&T enclosure are
pressurised. This can cause damage, short-circuiting or electrical
shocks.
• Do not expose the equipment to extreme temperatures. This can cause
deformation of the enclosure or damage to internal components.
• Repairs or adjustments to the equipment may only be undertaken by
Orlaco.
• The equipment must be assembled as shown in this manual.
• If there have been alterations or changes to this equipment that have
not been specifically approved by Orlaco, use of this equipment is not
permitted.
Statement related to Machine-directive 2006/42/EC:
Orlaco, under it’s role as manufacturers product-responsibility has
studied the impact of the Machine Directive onto the design of this
Pan/Tilt unit. We can make the following statement:
There is no risk that we aware of in the PTZ that is in conflict with the
Machine Directive and this device is safe to use under 2006/42/EC
machinery directive. :
2 safety measurements are in place to comply to the rules set out in the
directive:
1. Holes that are big enough to allow bodyparts in (see directive
for definition) are designed in a way that they cannot and will not
pinch the body-parts in normal operation of the PTZ as described
in this manual.
2. In the rare occasion that the device is hitting or pinching a
mechanical part or bodypart the electronics and integrated
sensors makes sure the stepping motors are stopped
automatically to prevent any damage similar to the way car
windows are functioning.
Before you start using this equipment, please read this manual carefully
and follow all instructions. This installation manual describes the func-
tions of the equipment, outlines the connection options and explains how
to put the equipment into operation. We recommend that you keep this
manual in a safe place for reference purposes.
If you have any questions or issues concerning the operation of this
equipment, consult the relevant section in the manual or contact the
Orlaco Products BV Service department.
The camera and monitor systems from Orlaco comply with the latest CE,
ADR, EMC and mirror-directive regulations. All products are manufac-
tured in accordance with the ISO 9001 quality management, ISO/TS16949
quality automotive and ISO 14001 environmental management.
Installation Manual
1. Introduction
PTZ (Pan Tilt Zoomcamera) unit.
Pan & Tilt unit including camera. The PTZ unit functions via two stepper
motors. These stepper motors are controlled by the integrated micro-
controller and input commands RS232 RS485/Visca-, Pelco D protocol/P
9600 Baud rate. Commands for the PTZ unit are sent via, amongst other
things, the Monitor 7” RLED Serial or Monitor 12” Serial. Weather-,
shock-, vibration-, corrosionproof.
2. Configuration
The space required for panning and tilting is:
Panning: 315mm.
Tilting: 370mm.
See also figure 10, page 7. When positioning the PTZ unit, account must
be taken of the space required for panning and tilting. There must be no
obstacles in this space.
3. Mounting
The PTZ unit has a base. Mount the PTZ unit upright.
The
PTZ
unit may not be mounted hanging or at a right
angle! This would put too much pressure on the base
and mechanical components.
First demount two coverplates of the PTZ unit, see figure 3.
To affix the PTZ unit, use a pole bracket or a wall bracket. Or mount the
PTZ unit directly to a metal surface.
Note the starting position of the camera; this is indicated as the zero posi-
tion in figure 1.
Use a Allen key to secure the PTZ unit with three M8 x 20mm Stainless
steel bolts(included). The base of the PTZ unit has three recessed holes.
Mount the bolts (Hexagon socket countersunk head screws) from the up-
per side of the base. For details of the size of the attachment points, see
figures 5 and 6. Mount the two cover plates back to the PTZ unit.
3.1. Mounting safety cables
Mount the fall protection to a fixed point. Use three cable clamps for
attachment. These cable clamps must to be installed correctly; see figure
2. Mount the safety cable from the camera to a fixed mounting point on
the same surface and height as the Base plate, see figure 4.
4. Operation
4.1 Overpressure in the enclosure
The enclosure of the Camera and PTZ unit has a 1,4-bar overpressure.
4.2 Switching on and off
First of all, position the PTZ unit in the zero position as indicated in
figure 1.
The PTZ unit configuration is switched on by connecting the connector
cables to the power supply. It is switched off by disconnecting the con-
necting cable from the power supply. See figure 7.
Ensure that the PTZ unit and other components of
the installation are closed so that it is not possible to
come into contact with moving parts.
Ensure that all parts are firmly fixed, stable and
secure.
Check that the power and connector cables are suit-
able for the system power supply.
Do not get too close to the PTZ unit when the system
is switched on. There is a risk of injury.
Contens page
1. Introduction
3
2. Configuration
3
3. Mounting
3
3.1. Mounting safety cables
3
4. Operation
3
4.1 Overpressure in the enclosure
3
4.2 Switching on and off
3
5. Electrical installation
4
5.1. Pan & Tilt (PTZ) cable specifications
4
5.2. Example configuration
4
6. Instructions for use
5
7. Troubleshooting
5
8. Maintenance and cleaning
6
9. Technical specifications
6
9.1 Camera PAL
6
9.2 PTZ PAL
6
9.3 General PAL
6
9.4 Camera NTSC
7
9.5 PTZ NTSC
7
9.6 General NTSC
7
10. Dimensions
7
11. Visca protocols
8
10.1 Orlaco Pan/Tilt command set
8
10.2 Old Pan/Tilt commands
8
10.3 New pan/Tilt commands
8
12. Generic Serial commands
8
13. Pan/Tilt serial commands
8
12.1 Old Pan/Tilt commands
9
12.2 New pan/Tilt commands
9
14. Additional serial commands
10
15. Disposal
11
16. General terms and conditions
11
17. Release notes
11
Available documentation
DS0506910 Camera PTZ SSt (0516910)
DS0506951 Camera PTZ Alu (0516950
DS0506960 Camera PTZ NTSC Alu (0516960)
UM0972080 Monitor 7" RLED/LEDD
Figure 1
Figure 3
Horizontal zero position
view direction
Cover plate
Cable Base
art. no 1221300
length 5,5m
Open
wired
Cable
fall protection
Base
Base plate
Cover plate
Cover plate
3 Bolts M8 x 20mm
Base
Base plate
Socket head wrench
Socket head wrench
M5 Socket head screw
Fall protection
Fall protection
Figure 2
