D1-2
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE
Operate within 4~5 seconds after the reel disk begins to
turn.
Install the Torque Gauge (JG002F) and Adapter (JG002B)
on the S Reel. Set to the Rewind mode. (Refer to Fig.1-4)
Then, confirm that it indicates 120~180gf•cm.
1.
2.
3.
NOTE
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) (Refer to Fig. 1-4)
Set to the STOP mode.
Move the Idler Ass'y from the S Reel.
Install the Torque Gauge (JG002F) and Adapter
(JG002B) on the S Reel. Turn the Torque Gauge
(JG002F) clockwise.
Then, confirm that it indicates 60~100gf•cm.
1.
2.
3.
4.
(T Reel Brake) (Refer to Fig. 1-4)
Set to the STOP mode.
Move the Idler Ass'y from the T Reel.
Install the Torque Gauge (JG002E) and Adapter
(JG002B) on the T reel. Turn the Torque Gauge
(JG002E) counterclockwise.
Then, confirm that it indicates 45~70gf•cm.
1.
2.
3.
4.
Fig. 1-4
NOTE
If the torque is out of the range, replace the following
parts.
Check item
1-4
1-5
Replacement Part
Idler Ass'y/Clutch Ass'y
T Brake Spring/Tension Spring
2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM
Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because
of long term usage or failure, the confirmation and
adjustment are necessary.
2-1: GUIDE ROLLER
Playback the VHS Alignment Tape (JG001 or JG001B).
(Refer to SERVICING FIXTURE AND TOOLS)
Connect CH-1 of the oscilloscope to TP4002 (Envelope)
and CH-2 to TP4001 (SW Pulse).
Press and hold the Tracking-Auto button on the remote
control for more than 2 seconds to set tracking to center.
Trigger with SW Pulse and observe the envelope. (Refer
to Fig. 2-1-A)
When observing the envelope, adjust the Adjusting Driver
(JG005) slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that flatness
is not moved so much.
Adjust so that the A : B ratio is better than 3 : 2 as shown in
Fig. 2-1-B, even if you press the Tracking Button to move the
envelope (The envelope waveform will begin to decrease
when you press the Tracking Button).
Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
1.
2.
3.
4.
5.
6.
7.
Torque Gauge/Adapter
(JG002F/JG002B)
T Reel
S Reel
Torque Gauge/Adapter
(JG002E/JG002B)
NOTE
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
Fig. 2-1-A
Max
A : B
≥
3 : 2
A
Entrance
Exit
Max
B
Fig. 2-1-B
CH-2
SW Pulse (TP4001)
CH-1
Track
CH-2
Track
CH-1
Envelope
(TP4002)
Envelope
CH-3
Audio
(1)
(2)
