background image

INTRODUCTION

Thank you for your purchase of Orion's HCCA-D600 power amplifier. Each Orion amplifier
is designed to be the leader in its class offering the most power, advanced features, and
extreme ease of use. In high-end sound systems or high SPL systems, Orion amplifiers will
give you years of trouble-free performance.

HCCA-D600 -

600 Watt single-channel Class D amplifier with built-in fully variable

high-pass, low-pass, or band-pass crossover with INTELLi BASS. Equipped with
optional remote gain, the 600D is capable of one-channel operation with a max-
imum power of 600 Watts into 1

W

.

The installation of all Orion components will determine the overall performance result.
Improper installation will not only limit the performance of your Orion system but also
potentially compromise the reliability of this amplifier. To ensure proper sonic results and
component reliability, please refer to your authorized Orion dealer for installation assis-
tance or advice. If you decide to perform the installation yourself, be sure to read the entire
manual before beginning the installation.

What’s in the Box

(1) Amplifier

(1) Spare fuse

(1) Allen wrench 2.5mm

(1) Allen wrench 3mm

(1) Hardware pack (screws and washers)

(1) Amplifier installation and operation manual

(1) Orion vinyl window sticker

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanent hearing
loss. High power automotive sound systems can generate sound pressure levels in excess of
130dB. When playing your system at high levels, please use hearing protection and avoid
long term exposure.

2

© 2005 Directed Electronics—all rights reserved

Summary of Contents for HCCA-D600






















Reviews: