background image

1

2

Thank you for  purchasing our car audio amplifier. These power amplifier has been 

designed to  provide high quality  performance  with  minimum 

maintenance. However, it's   performance  will  only be as   good  as  the  care  and 

quality of  components with which is installed.  We therefore    advise that you read 

these  instructions very carefully to familiarize  yourself  with  the  product  and  it's 

features.

Before installing the power amplifier please read this instruction  manual carefully.

The instructions  for mounting and connecting the set have to be followed precisely.

 If necessary, a service center should be consulted.

All  connection  for DC  power,  signal input and speaker outputs can be carried out 

easily and safely by way of RCA and screwed terminals.

Please  choose a mounting place without any direct weather  influences. Note that 

the amplifier generates   heat   so   that  a well  ventilated  place  is  necessary.

According to your car's  construction the set can be made very carefully in order to 

ensure the amplifier's full performance and reliability.

Keep   the  wire  connections  as  short   as   possible   with    sufficient    length   in 

order  to  minimize power  losses  and provide  a higher audio output of the system.

For  safety   reasons  route  all  power  and speaker wiring by using the exiting wire

channels.

To minimize  damage  to  the  cables,  take care that they  do not pass sharp edged 

metal.

Lay   all  cables  as   far  away  as  possible from the ignition cables, modules in the 

boot   and under the key dashboard, as these create interference.

Add  a  fuse  into the  (+)  power cable in a distance of not  more than30cm from the

positive battery pole.

Keep  the  length of  the power wires as short as possible .  It is better to use  power 

cables which are short and then longer speaker cables.

In order to reduce interference ,  please   pay attention  to  the  wiring  instructions. 

INTRODUCTION

INSTALLATION INSTRUCTIONS

TABLE OF CONTENTS

To ensure your warranty, please record the following information regarding 

your new amplifier.

RECORD YOUR SERIAL NUMBER AND DATE

Model:

Serial Number:

Date of Purchase:

Purchased from:

Introduction.........................................................................................2

Installation Instructions...................................................................... .2

Record Your serial Number And Date.................................................... 2

Functions....................................................................................... 3~4

Operation ...........................................................................................5

Trouble Shooting................................................................................. 5

Precautions ........................................................................................6

Fuse Replacement.............................................................................. 6

Stereo Mode ...................................................................................7~8

Speakers Connections................................................................... 9~12

Bridged Mode.............................................................................. 13~14

Power Connection Leads................................................................... 15

Wiring Instructions............................................................................ 16

Operation .........................................................................................17 

Interference ......................................................................................18

Specification ...............................................................................19~21

Summary of Contents for CO1000.4 Cobalt













Reviews: