Q I G
Quick Installation Guide
PRINTED ON RECYCLED PAPER
Version 1.0
Q
uick
I
nstallation
G
uide
1. Launch the Internet Explorer and type in IP address of the switch. The default static IP
address is
192.168.10.1
2. Log in with default user name and password (both are
).
After logging in, you
admin
should see the following screen. For more information on configurations, please refer
to the user manual. For information on operating the switch using ORing
’
s Open-Vision
management utility, please go to ORing website.
Specifications
ORing Switch Model
Physical Ports
Technology
Ethernet Standards
Slot Number
RS-232 Serial Console Port
Switch Properties
Security Features
Device Binding security feature
Enable/disable ports, MAC based port security
Port based network access control (802.1x)
VLAN (802.1Q ) to segregate and secure network traffic
Radius centralized password management
SNMPv3 encrypted authentication and access security
Https / SSH enhance network security
MAC-based authentication(802.1x)
Guest VLAN
Web and CLI authentication and authorization
IP source guard
Software Features
Hardware routing, RIP , VRRP and static routing
IEEE 802.1D Bridge, auto MAC address learning/aging and MAC address (static)
Multiple Registration Protocol (MRP)
STP/RSTP/MSTP (IEEE 802.1D/w/s)
Redundant Ring (O-Ring) with recovery time less than 30ms
TOS/Diffserv supported
Quality of Service (802.1p) for real-time traffic
VLAN (802.1Q) with VLAN tagging
IGMP Snooping
IP-based bandwidth management
Application-based QoS management
DOS/DDOS auto prevention
Port configuration, status, statistics, monitoring, security
DHCP Server/Client/Relay
SMTP Client
NTP server
Modbus TCP
Network Redundancy
O-Ring
O-Chain
MRP
*NOTE
MSTP (RSTP/STP compatible)
RS-232 in RJ45 connector with console cable. 115200bps, 8, N, 1
(support backup unit)
RGS-ME-HV
6
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3ab for 1000Base-T
IEEE 802.3z for 1000Base-X
IEEE 802.3x for Flow control
IEEE 802.3ad for LACP (Link Aggregation Control Protocol)
IEEE 802.1p for COS (Class of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spanning Tree Protocol)
IEEE 802.1s for MSTP (Multiple Spanning Tree Protocol)
IEEE 802.1x for Authentication
IEEE 802.1AB for LLDP (Link Layer Discovery Protocol)
Switching latency: 7 us
Switching bandwidth: 176Gbps
Throughput (packet per second) : 130.94Mpps@64Bytes packet
Max. Number of Available VLANs: 4095
VLAN ID Range: VID 1 to 4094
IGMP multicast groups: 128 for each VLAN
Port rate limiting: User Define
MAC Table
32K
Processing
Store-and-Forward
Priority Queues
8
Power
Environmental
-40 to 85 C (-40 to 185 F)
o
o
Storage Temperature
Operating Temperature
Physical Characteristic
Dimension (W x D x H)
Weight (g)
5.8 kg (without module)
Regulatory Approvals
Enclosure
2U 19 inches rack mountable, IP-30
444.5 (W) x 422 (D) x 86.2 (H) mm (17.49 x 16.61 x 3.39 inches)
EN 55032, CISPR32, EN 61000-3-2, EN 61000-3-3, FCC Part 15 B class A
EMI
EN 55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT),
IEC/EN 61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8 (PFMF), IEC/EN 61000-4-11 (DIP)
EMS
IEC60068-2-27
Shock
IEC 60068-2-31
IEC60068-2-6
Vibration
EN62368-1 (LVD)
Safety
Free Fall
Warranty
5 years
0 to 60 C (32 to 140 F)
o
o
Packet Buffer
32Mbits
CE EMC (EN 55024, EN 55032), EN50121-4 (compliant), FCC Part 15 B
EMC
MTBF
412139 hours
NOTE: This function is available by request only
ORing Industrial Networking Corp.
Copyright© 2019 ORing
All rights reserved.
TEL: +886-2-2218-1066
FAX: +886-2-2218-1014
Website: www.oringnet.com
E-mail: [email protected]
Optional Module
SWM-80GT-E
SWM-08GP-E
SWM-44GTP-E
Configurations
Wiring
Grounding
Grounding and wire routing to help limit the effects of noise due to electromagnetic
interference (EMI). Run the ground connection from the ground screws to the grounding
surface prior to connecting devices.
Power inputs
RGS-ME-HV supports dual 100~240VAC/125-370VDC
power inputs, Power Supply 1 (PWR1) and Power Supply 2 (PWR2).
The connections for PWR1 and PWR2 are located on the terminal
block.
STEP 1:
Remove the transparent protective cover from the terminal block
STEP 2:
Insert the negative/positive DC wires into the V-/V+ terminals, respectively.
STEP 3:
To keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten
the wire-clamp screws on the front of the terminal block connector.
STEP4:
After wiring is completed, put the transparent cover back to the terminal block.
After installing the switch card, the green power LED should turn on. Please
refer to the following tablet for LED indication.
LED
Color
Status
Description
PWR
Green
On
System ready
Blinking
Upgrading firmware
PWR1
Green
On
AC power module1 activated
PWR2
Green
On
AC power module2 activated
R.M
Green
On
System running in Ring Master mode
Ring
Green
On
System running in Ring mode
Blinking
Ring structure is broken
Fault
Amber
On
Unexpected event occurred
Module
Green
On
Module slot is connected
1G/10GBase-X SFP+ ports
LNK/ACT
Green
On
Port is connected
Blinking
Transmitting data
To reboot the switch, press the
button for 3 seconds.
Reset
To restore the switch configurations back to the factory defaults, press the
button for 5
Reset
seconds.
Resetting
1G/10Gbase-X with SFP+
4
Power consumption(Typ.)
68.8W
Overload current protection
Present
Redundant Input power
Dual 100~240VAC/125~370VDC power inputs
Reverse Polarity Protection
Present
RGS-ME-HV
Q I G
RGS-ME-HV
M A N A G E D
Rack-Mount
GIGABIT
SWITCH
Industrial Layer 3 modular rack mount
Managed Gigabit Switch
LAYER 3
Jumbo frame
Up to 10K Bytes
Fault contact
Relay
None
Reset Function
Reset Button
< 5 sec: System reboot, > 5 sec: Factory default
5% to 95% Non-condensing
Operating Humidity
SWM-44GTP-E