Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
RGS-ME-HV
Q I G
RGS-ME-HV
1907-200-MH1-FX010
RGS-ME-HV
is Layer-3 modular managed redundant ring
Ethernet switch with 6 slots, up to 48 ports, and has 4 fixed 10G SFP+ ports.
With such high port density and modular design, it makes network planning
easier. With completely support of Ethernet Redundancy protocol, O-Ring
(recovery time < 30ms) and MSTP (RSTP/STP compatible) can protect your
mission-critical applications from network interruptions or temporary
malfunctions with its fast recovery technology. And support wide operating
temperature from 0 C to 60 C.
can also be managed
o
o
RGS-ME
centralized and convenient by Open-Vision, as well as the Web-based
interface, Telnet and console (CLI) configuration. Therefore, the switch is one
of the most reliable choice for highly-managed and Fiber Ethernet.
M A N A G E D
Rack-Mount
GIGABIT
SWITCH
Panel Layouts
1
9
12
1. Power input module slots
2. AC power input
Package Contents
Front View
Rear View
Network Connection
Console cable
To connect the console port to an external
management device, you need an RJ-45
to DB-9 cable, which is also included in
the package. Please see the table for the
console port pin assignment information.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
The series have standard Ethernet ports. According to the link type, the switch uses CAT 3, 4, 5, 5e
UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs).
Please refer to the following table for cable specifications.
1000 Base-T RJ-45
Pin Number
Assignment
1
BI_DA+
2
BI_DA-
3
BI_DB+
4
BI_DC+
5
BI_DC-
6
BI_DB-
7
BI_DD+
8
BI_DD-
10/100 Base-T(X) MDI/MDI-X
Pin Number
MDI port
MDI-X port
1
TD+(transmit)
RD+(receive)
2
TD-(transmit)
RD-(receive)
3
RD+(receive)
TD+(transmit)
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
7
Not used
Not used
8
Not used
Not used
10/100 Base-T(X) RJ-45
Pin Number
Assignment
1
TD+
2
TD-
3
RD+
4
Not used
5
Not used
6
RD-
7
Not used
8
Not used
1000Base-T MDI/MDI-X
Pin Number MDI port MDI-X port
1
BI_DA+
BI_DB+
2
BI_DA-
BI_DB-
3
BI_DB+
BI_DA+
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB-
BI_DA-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
RS-232 baud rate setting: 9600, 8, N, 1
With 10/100BASE-T(X) cables, pins 1 and 2 are used for transmitting data. and pins 3 and 6
are used for receiving data. The device also supports auto MDI/MDI-X operation. You can use
a cable to connect the switch to a PC.
For pin assignments for different types of cables, please refer to the following tables.
PC pin out (male)
assignment
RS-232 with DB9
female connector
DB9 to RJ 45
Pin #2 RD
Pin #2 TD
Pin #2
Pin #3 TD
Pin #3 RD
Pin #3
Pin #5 GND
Pin #5 GND
Pin #5
Dimension
Unit =mm (Tolerance ±0.5mm)
Contents
CD
RGS-ME-HV
Pictures
Number
X 1
X 1
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
QIG
Console Cable
X 2
X 1
X 1
Rack-mount Kit
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mechanical Loading:
Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Safety & Warnings
Industrial Layer 3 modular rack mount
Managed Gigabit Switch
LAYER 3
Circuit Overloading:
Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
External metal parts of this equipment are extremely hot!! Before touching the equipment, be
sure to protect your hands and body from serious injury.
6
5
4
3
2
1
4
3
2
1
10G SFP+
Module
Fault
Reset
Console
115200,8,N,1
Ring
R.M.
2
PWR
1
RGS-ME
8
8
.0
0
6
5
4
3
2
1
4
3
2
1
10G SFP+
Module
Fault
Reset
Console
115200,8,N,1
Ring
R.M.
2
PWR
1
RGS-ME
2 3 4 5 6 7
8
10
11
1. Power LED
2. Power2 LED
3. Power1 LED
4. R.M. status LED
5. Ring status LED
6. Faulty relay indicator
7. Reset button
8. Console port
9. Module status LEDs
10. 1G/10GBase-X SFP+ ports
11. Link/Act LED for SFP+ ports
12. Ethernet module slots
1
2
Installation
Rack-mounting
Step 1:
Install left and right front mounting brackets to the switch using 6 M3 screws on each side
provided with switch.
Step 2:
With front brackets orientated in front of the rack, nest front and rear brackets
together. Fasten together using remaining M4 screws into counter sunk holes.
Step 3:
Fasten the front mounting bracket to the front of the rack.