IGPS-9042GP
PWR
PWR1
PWR2
R.M
Ring
Fault
G3
G4
G1
G2
Reset
1
2
3
4
802.3at/af PoE
G6
100/1000X
G5
G6
10/100/1000T
G5
Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
The
is a full-Gigabit managed PoE Ethernet switch with
four 10/100/1000Base-T(X) P.S.E. ports and two 100/1000Base-X SFP
ports. The former supports IEEE 1588v2 clock synchronization while the
latter does not. With complete support for Ethernet redundancy protocols
such as O-Ring (recovery time < 30ms over 250 units of connection) and
MSTP (RSTP/STP compatible), the device can protect mission-critical
applications from network interruptions or temporary malfunctions with fast
recovery technology. The four 10/100/1000Base-T(X) P.S.E. ports enable
the device to provide sufficient power for power-hungry devices with up
to 30w per port. With a wide operating temperature from -40 C to 75 C, the
device can be managed centrally via ORing’s proprietary Open-Vision
platform as well as via Web-based interfaces, Telnet and console (CLI).
IGPS-9042GP-24V
o
o
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Safety & Warnings
Dimension
Panel Layouts
12
1. Reset button
2. PWR status LED
3. PWR1 LED
4. PWR2 LED
5. R.M. status LED
6. Ring status LED
7. Faulty relay indicator
8. Console port
9. PoE indicators for LAN ports
10. SFP Ports
11. Link/Act LED for SFP ports
12. Gigabit PoE LAN ports
13. Link/Act LED for Gigabit LAN
ports
14. Speed LED for LAN ports
Package Contents
Contents
DIN-rail Kit
CD
IGPS-9042GP-24V
Pictures
Number
X 1
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
QIG
Console Cable
X 1
X 1
X 1
Wall-mount Kit
13
Rear View
1
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
1. Terminal blocks: PWR1, PWR2
, Relay
1
Installation
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Step 2:
Step 3:
Screw the wall-mount kit onto the rear panel of the switch. A total of six
screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
IGPS-9042GP-24V
Q I G
IGPS-9042GP-24V
1907-2-29-IGPS9042GP-1.0
Mechanical Loading:
Circuit Overloading:
Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
54.3
32.2
45.0
14.0
40.0
50.0
25.3
33.6
12.5
54.3
145.1
108.5
32.0
32.2
1
16.0
18.0 18.15
51.0
209.3
7.35
187.4
R2.5
R3.95
46.0
8
2
3
4
5
6
7
1
GIGABIT
I N D U S T R I A L
SWITCH
PoE
Industrial Managed PoE Gigabit Switch
9
IGPS-9042GP
PWR
PWR1
PWR2
R.M
Ring
Fault
G3
G4
G1
G2
Reset
1
2
3
4
802.3at/af PoE
G6
100/1000X
G5
G6
10/100/1000T
G5
IGPS-9042GP
PWR
PWR1
PWR2
R.M
Ring
Fault
G3
G4
G1
G2
Reset
1
2
3
4
802.3at/af PoE
G6
100/1000X
G5
G6
10/100/1000T
G5
10
11
14
