IES-3160
P1
P3
P5
P1
P3
P2
P4
P6
P8
P7
P13
P9
P11
P10
P12
P14
P16
P15
PWR
PWR1
PWR2
Quick Installation Guide
Version 2.1
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
is managed Redundant Ring Ethernet switch with 16x10/100Base-
IES-3160
T(X) ports. With completely support of Ethernet Redundancy protocol, O-
Ring (recovery time < 10ms over 250 units of connection), O-Chain,
MRP
and MSTP/RSTP/STP (IEEE 802.1s/w/D) can protect your
*NOTE
mission-critical applications from network interruptions or temporary
malfunctions with its fast recovery technology. O-Chain is the revolutionary
network redundancy technology that provides the add-on network
redundancy topology for any backbone network, O-Chain allows multiple
redundant network rings of different redundancy protocols to join and
function together as a larger and more robust compound network topology.
O-Chain providing ease-of-use while maximizing fault-recovery swiftness,
flexibility, compatibility, and cost-effectiveness in one set of network
redundancy topology. All function of
can be managed centralized
IES-3160
and convenient by a powerful windows utility — Open-Vision. In addition, the
wide operating temperature range from -40 to 75 C can satisfy most of
o
operating environment. Therefore, the switch is one of the most reliable
choice for highly-managed Ethernet application.
Package Contents
The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Safety & Warnings
Dimension
Panel Layouts
Front View
IES-3160
1907-200-XX
Contents
Console Cable
CD
IES-3160
Pictures
Number
X 1
X 1
X 1
QIG
X 2
X 1
Wall-mount Kit
Rear View
1. Din-rail screw holes
2. Wall-mount screw holes
Step 1:
Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
device. A total of six screws are required, as shown below.
Step 2:
Use the device, with wall mount plates attached, as a guide to mark the
correct locations of the wall-mounting screws.
Step 3:
Insert a screw head through the large part of the keyhole-shaped aperture on the
plate, and then slide the device downwards. Tighten the screw for added stability.
Wall-mounting
Step 1:
Slant the device and screw the Din-rail kit onto the back of the device, right in the
middle of the back panel.
Step 2:
Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks
into the rail firmly.
DIN-rail Installation
1
2
2
Bottom View
1
2
1. Terminal block
2. Grounding screw
Installation
66.0
5
0
.0
2
6
.0
4
3
.0
4
3
.0
4
3
.0
74.3
1
1
6
.0
40.0
18.0
107.5
1
5
3
.6
74.3
8
.0
8
0
.5
Unit =mm (Tolerance ±0.5mm)
X 1
DIN-rail Kit
IES-3160
Industrial Managed Ethernet Switch
SWITCH
I N D U S T R I A L
*NOTE : This function is available by request only.
The product is open type, intended to be installed in and industrial control panel or an
enclosure.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation of the
equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading
Circuit Overloading:
Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
IES-3160
P1
P3
P5
P1
P3
P2
P4
P6
P8
P7
P13
P9
P11
P10
P12
P14
P16
P15
PWR
PWR1
PWR2
7
1
2
3
4
5
6
10
8
9
11
1. Power LED
2. PWR1 LED
3. PWR2 LED
4. R.M. status LED
5. Ring status LED
6. Faulty relay indicator
7. Console port
8. Link/Act LED for Ethernet port
9. Full/Half-duplex indicator
10. LAN ports
11. Reset button
PWR-1
PWR-2
1A@24V
DC12-48V
V2- V2+ V1- V1+
Fault
IES-3160
P1
P3
P5
P1
P3
P2
P4
P6
P8
P7
P13
P9
P11
P10
P12
P14
P16
P15
PWR
PWR1
PWR2
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses CAT
3,4,5,5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45