background image

13

www.origineffects.com

Origin Effects MAGMA57

Appendix D: Safety notices

General safety

Keep these instructions and heed all warnings. Do not use this apparatus near water. Clean only with 
a dry cloth. Do not install near any heat sources such as radiators, heat registers, stoves or other 

apparatus (including amplifiers) that produce heat. Refer all servicing to qualified service personnel. No 

user serviceable parts inside.

When using an external power supply, use only attachments/accessories specified by Origin Effects. 

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, 
and the point where they exit from the apparatus. Do not defeat the safety purpose of the polarised or 
grounding-type plug. A polarised plug has two blades with one wider than the other. A grounding type 
plug has two blades and a third grounding prong. The wide blade or the third prong are provided for 

your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the 

obsolete outlet. Unplug this apparatus during lightning storms or when unused for long periods of time.

FCC certification

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for MAGMA57















Reviews: