Orientalmotor FPW Series, Operating Manual

Page: 2 / 4

2
Warning label
To prevent the risk of damage to equipment, leave nothing
around the motor that would obstruct ventilation.
To prevent bodily injury, do not touch the rotating parts (output
shaft) of the motor during operation.
When an abnormality is noted, turn off the power immediately,
or fire, electric shock or injury may occur.
The motor’s surface temperature may exceed
70 °C, even under normal operating conditions.
If a motor is accessible during operation, post
the warning label shown in the figure in a
conspicuous position to prevent the risk of
burns.
To dispose of the motor, disassemble it into parts and
components as much as possible and dispose of individual
parts/components as industrial waste.
Preparation
Checking the product
Upon opening the package, verify that the items listed below are
included. Report any missing or damaged items to the branch or sales
office from which you purchased the product.
•
Motor .................................. 1 unit
•
Capacitor............................. 1 piece (only for single-phase motors)
•
Capacitor cap ...................... 1 piece (only for single-phase motors)
•
Operating manual................ 1 copy
•
Set of mounting bolts.......... 1 set
(Mounting screws, Nuts, Washers 4 pieces each, Key 1 piece)
Checking the model name
Check the model number against the number indicated on the product.
●
100 V/110 V/115 V type
Model Motor model Capacitor model
FPW425A2- J FPW425A2- CH80CFAUL2
FPW425A2- U FPW425A2- CH65CFAUL2
FPW540A2- J FPW540A2- CH110CFAUL2
FPW540A2- U FPW540A2- CH90CFAUL2
FPW560A2- J FPW560A2- CH180CFAUL2
FPW560A2- U FPW560A2- CH120CFAUL2
FPW690A2- J FPW690A2- CH250CFAUL2
FPW690A2- U FPW690A2- CH180CFAUL2
●
200 V/220 V/230 V type
Model Motor model Capacitor model
FPW425C2- J FPW425C2- CH20BFAUL
FPW425C2- E FPW425C2- CH15BFAUL
FPW540C2- J FPW540C2- CH30BFAUL
FPW540C2- E FPW540C2- CH23BFAUL
FPW560C2- J FPW560C2- CH40BFAUL
FPW560C2- E FPW560C2- CH30BFAUL
FPW690C2- J FPW690C2- CH60BFAUL
FPW690C2- E FPW690C2- CH45BFAUL
FPW425S2- FPW425S2-
－
FPW540S2- FPW540S2-
－
FPW560S2- FPW560S2-
－
FPW690S2- FPW690S2-
－
The gear ratio appears at the model number indicated by the box ( ).
Installation
Location for installation
Install the motor in a well-ventilated location that provides easy access
for inspection. The location must also satisfy the following conditions:
•
Indoors
•
Operating ambient temperature
− 10 to +40 °C (+14 to +104 °F) (non-freezing)
− 10 to +50 °C (+14 to +122 °F) for 100 V/200 V
•
Area that is free from an explosive atmosphere or toxic gas (such as
sulfuric gas) or liquid
•
Area not exposed to direct sun
•
Area free of excessive salt
•
Area not subject to continuous vibration or excessive shocks
•
Area free of excessive electromagnetic noise (from welders, power
machinery, etc.)
•
Area free of radioactive materials, magnetic fields or vacuum
•
1000 m or less above sea level
How to install the motor
Drill holes in the mounting plate and fasten the motor to the mounting
plate with screws, nuts, and washers. Be sure that no gaps are left
between the gearhead pilot section of the mounting plate.
The maximum plate thickness applicable when the supplied screws are
used is 10 mm (0.39 in.).
Installation holes
4-ØD
C
ØB
ØA
Installation hole dimensions
[mm (in.)] Model
ØA ØB C 4-ØD
Size of key
[mm (in.)]
FPW
425
94
(3.70)
34
(1.34)
15
(0.59)
5.5
(0.22)
4×25
( 0.1575×0.984)
FPW
540
104
(4.09)
36
(1.42)
18
(0.71)
6.5
(0.26)
4×25
( 0.1575×0.984)
FPW
560
104
(4.09)
34
(1.34)
18
(0.71)
6.5
(0.26)
5×25
( 0.1969×0.984)
FPW
690
120
(4.72)
42
(1.65)
20
(0.79)
8.5
(0.34)
6×25
( 0.2362×0.984)
Note
ØB indicates the external dimension of the gearhead boss.
Provide a hole with a sufficient allowance.
Nuts
Washers
Motor
Mounting plate
Screws provided
with motor
Mounting screws
Size of mounting screws
Model
Thread size Length [mm (in.)]
Tightening
torque
[N·m (lb-in.)]
FPW425 M5 P0.8 80 (3.15) 3.8
（
33
）
FPW540
M6 P1.0 90 (3.54) 6.4 (56)
FPW560
M6 P1.0 90 (3.54) 6.4 (56)
FPW690 M8 P1.25 100 (3.94) 15.5 (137)
Note
Do not disassemble the gearhead from the motor.
Be sure to use the supplied screws and tighten within the
specified torque in order to ensure proper water proof fit.