background image

4

fig. 1

Before assembling appliance, remove two screws 

from the connector assembly. Remove cardboard 

insert by pulling upward.

fig. 2

With ON/OFF switch facing the front of the unit, 

slide upper handle section over matching section 

of the connector assembly. Insert short screw into 

top hole and long screw into the bottom hole then 

tighten firmly until handle is no longer loose.

fig. 3

Attach cord to cord clip by pressing cord above 

and below clip ensuring the cord is fully rested in 

clip. 

fig. 4

Insert plug on cord assembly into handle. 

Make sure disposable paper filter dust bag is in place. 

DO

NOT 

operate the cleaner without a paper filter dust bag. Plug

the power cord into an electrical outlet and press the 

On (l) -

OFF(O) 

switch on Helping Handle Assembly when ready to

operate.

Up-Position Lock

fig. 5

Place foot on power head and lean handle back 

gently to release lock for vacuum use. Return 

handle to the full upright position to engage lock.

NOTE: 

Do not operate the unit while in the upright and locked

position.  Do not let the unit run while in any one stationary

position for any period of time. Keep the unit moving while in

operation.

For Easy Power Cord Storage

fig. 6

Wrap power cord around cord dump on Helping 

Hand

®

handle and cord hook on connector. 

Secure to "U" shaped part on plug

fig. 7

To release cord, twist cord dump located on 

Helping Hand

®

handle 1/2 turn. Slide cord off 

handle.

WARNING: Unplug cord from electrical outlet
before servicing.

fig. 8

Unzip outer bag completely.

fig. 9

Pull bag cardboard collar to release bag dock 

door from connector. Bag dock door will hinge 

downward.

fig. 10

Gently pull bag cardboard collar upward out of 

the bag dock.  Dust seal will close automatically.

fig. 11

Slide the cardboard collar completely onto bag 

dock door.

fig. 12

Firmly push bag dock door with both thumbs on 

indication point until it snaps.

General Information

T

R

eplace 

F

ilter 

D

ust 

B

ag

7

8

9

6

10

11

12

Cord dump

Bag Installation

PRESS  
UNTIL SNAP 
IS HEARD

ENFONCEZ JUSQU

’À 

ENTENDRE UN BRUIT

PRESIONE HASTA

      

ESCUCHAR UN          

CHASQUIDO DE SUJECIÓN

1

2

3

5

4

Upper 
Handle

Plug (Cord Assembly)

Connector
Assembly

Summary of Contents for XL2800HAY









Reviews: