background image

BAG REMOVAL:

1. Unsnap bag door from

base.

2. Gently pull

bag from
cardboard
collar
upwards.

BAG INSTALLATION:

1. Slide the cardboard collar

completely onto bag dock
door.

2. Firmly push bag dock door

with both thumbs on
indication point until 
it snaps.

4

To Replace Filter 

Dust Bag

WARNING: Unplug cord from
electrical outlet before servicing.

ENFONCEZ JUSQU

ENFONCEZ JUSQU’À

’À 

ENTENDRE UN BRUIT

ENTENDRE UN BRUIT

PRESIONE HAST

PRESIONE HASTA

A      

ESCUCHAR UN          

ESCUCHAR UN

CHASQUIDO DE SUJECI

CHASQUIDO DE SUJECIÓ

ÓN

N

ENFONCEZ JUSQU’À 

ENTENDRE UN BRUIT

PRESIONE HASTA      

ESCUCHAR UN          

CHASQUIDO DE SUJECIÓN

Before assembling appliance,
remove two screws from
connector assembly. Remove
cardboard insert by pulling
upward 

(fig 1)

.

With ON/OFF switch facing the
front of the unit, slide upper
handle tube over matching
section of the connector
assembly. Hold tab of cord

strain relief flush with 

TOP 

hole in connector assembly. Insert

screw through hole in tab of cord strain relief and firmly tighten
to connector assembly. Insert remaining screw in bottom hole of
connector assembly and tighten firmly 

(fig 2)

.

NOTE:

The power cord comes installed in the cord strain relief.

Should the power cord come loose, simply pinch the power cord
together and slide approximately 1 - 2 inches through hole in
cord strain relief. Carefully slide power cord over clamp on the
cord strain relief and pull excess until the power cord is tightly
rested under clamp. 

Attach cord to cord clip by pressing cord above and below clip

ensuring the cord is fully rested in clip 

(fig 3)

.

2

Assembly

Assembly

1

2

3

4

9

10

11

14

15

16

12

13

5

6

7

8

To assist you in identifying 
components of your vacuum, 
the parts have been numbered 
as follows:

1 Handle tube, upper
2 Tube, lower
3 Power head
4 Outer bag
5 Paper filter dust bag
6 Power cord
7 Retaining spring
8 Bag tension bar
9 Zip fastener

10 On/off switch
11 Cord hook
12 Plastic loop/cable clamp
13 Connector assembly
14 Fan housing
15 Cord assembly
16 Cord Strain Relief Assembly

1

3

TAB

Summary of Contents for XL 2635RH









Reviews: