© 2008 Oreck Holdings, LLC. All Rights Reserved. All word mark, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC. Printed in U.S.A.
5
53
34
40
09
9--0
01
1 R
RE
EV
V C
C 0
03
3//0
08
8 E
EC
CN
N#
# R
R--8
89
99
97
7
• Cleaning upholstery which is covered with fabrics that are not
compatible with wet cleaning may result in damage to the fabric.
Know what the fabric is and how it may be cleaned before using the
Oreck Steemer cleaner.
• Check the stuffing material if possible. Look inside cushions and
underneath the furniture. If the filling is colored, it may bleed through
and discolor the furniture. Most modern stuffing material is light
colored and colorfast.
• To remove loose dirt, vacuum upholstery thoroughly with a vacuum
cleaner.
• If the upholstery is being cleaned for the first time,
CHECK FOR
COLORFASTNESS.
Test a small area several hours before starting
to clean upholstery. Pour a small amount of Steemer Full Release
®
Professional Upholstery Shampoo on a clean white cloth and blot
upholstery. Examine the cloth for color removal. If color appears on
cloth, the upholstery is not colorfast and should not be cleaned with
wet extraction methods. Let test area dry completely. Inspect for
changes in color, bleeding, stretching or shrinkage. Test another area
if in doubt.
This product is not recommended for use on silk,
velvet, wool and some cotton blends.
To Clean Upholstery & Small Spill Pick-Ups:
Plug cord into an electrical outlet.
fig. 12
Turn the Shampoo/Rinse switch to the
“SHAMPOO”
position.
fig. 5
Test and reset A.L.C.I. on the plug.
fig. 11
Insert a specially formulated Steemer Full Release
®
Professional
Upholstery Cleaner Cartridge.
fig. 13
Turn cleaner on by placing the On/Off power switch in the
“ON”
position.
fig. 14
Lock the cleaner spray button by pressing and sliding the button
forward on the main handle.
fig. 18
Depress the dispensing trigger on the hand-held nozzle and
slowly drag the nozzle towards you. Make a second pass at right
angles to the first. This will minimize any streaking or uneven
appearance.
To Clean Carpet Cleaner
WARNING:
To reduce the risk of electric shock or injury from
moving parts, unplug before servicing.
Before turning the cleaner off, tilt the cleaner back, raising the nozzle off
the carpet for 15-20 seconds. This prevents extracted water in the
nozzle from dripping back onto the carpet after you turn the cleaner off.
fig. 13
Place the power switch in the
“OFF“
position. Unplug the power
cord from the outlet.
fig. 11
Remove the cleaner cartridge by rotating the locking lever
upwards.
Do not store with a cleaner cartridge installed.
fig. 8
Remove and empty the tank. Rinse out the lower recovery tank
with warm water.
fig. 19
Wipe off the inlet screen to remove accumulated dirt, lint and
debris.
fig. 10
Replace tank.
fig. 20
If you have been operating the cleaner at length, it may be
necessary to clean the nozzle from time to time, particularly if the
carpet is brand new or very dirty, or if long-haired pets frequently
use the carpeted area. Unplug cleaner and examine several
areas on the power nozzle to see if debris has built up:
a.
Extractor slots
b.
Brush roll chamber
c.
Spray Tips
fig. 20
To clean the Steemer extractor slots, place a cloth or towel over
the motor cover to shield and protect the motor from water
damage. Run hot tap water through the nozzle until clean.
To clean the brush chamber and spray tips, take a towel or damp
cloth and wipe clean.
To Store Cleaner
fig. 6
Pull the wheel assembly forward toward nozzle for compact
storage.
NOTE:
Do not store the cleaner in freezing conditions. Do
not store the cleaner with water in the tank. Do not store the
cleaner with cleaner cartridge installed. Turn the squeegee
upside down for storage. Squeegee will deform if left in
position while in storage.
Things To Do
• Use only manufacturer’s recommended attachments and accessories.
• Keep free of dust, lint, and hair.
• Turn off all controls before unplugging.
• Test the A.L.C.I. plug with every use.
• Empty the recovery tank when full and whenever clean water is
added to the supply tank.
• Keep young children and pets away from cleaned carpets until dry.
• Check carpets and upholstery for color fastness.
• Clean nozzle periodically.
To Replace Belt
WARNING:
To reduce the risk of electric shock or injury from
moving parts, unplug before servicing.
Replacement belts (53364-01) for Oreck Steemers are available from
Oreck. Call Toll-Free 1-800-989-3535 (US) or 1-888-676-7325 (Canada).
fig. 4
Unplug the power nozzle cord leading from the power head to
the rear of the main cleaner.
fig. 3
Remove the power nozzle from the main cleaner.
fig. 21
Disassemble Power Nozzle:
a.
Remove screw from belt cover.
b.
Remove two (2) screws holding the brush roll clamp in place and
remove clamp.
c.
Remove and replace the old belt if broken or if excessive wear is
noted.
To Install a New Belt:
fig. 21
Remove brush roll and insert the new belt into the rectangular
cavity. Using a long screwdriver, loop belt around motor shaft.
Pull and stretch belt over crowned end of the brush roll. Rotate
brush to properly align belt.
fig. 21
Replace belt cover, brush roll clamp and screws.
fig. 3
Reattach power nozzle to unit.
fig. 4
Reconnect power nozzle cord and power cord.
fig. 5
Test and reset A.L.C.I. on the plug.
To Clean Power Nozzle Cover
fig. 23
Remove two screws from top of cover
a.
Tilt cover forward and pull down to unhook tabs from slots in
Power Nozzle Housing.
b.
Clean cover and housing to remove debris.
c.
Hook cover tabs into slots on Power Nozzle Housing.
d.
Pivot cover backward and fasten with two screws.
