background image

2

fungi as a result. Moreover, it is also a fact that heating 
this humid air consumes more energy. 

It is, therefore, important to ventilate 24 hours per day.

If you have any questions, please contact your supplier. 
The contact details can be found in the installation and 
measurement report.  

2. How does the ventilation system work?

Your home is equipped with a mechanical extraction 

ventilation system from Orcon BV. This system consists 
of a centrally-located fan unit with a highly energy-

efficient EC motor, ductwork with extraction valves in 

the kitchen, bathroom, lavatory and possibly the storage 
area, all combined with a remote control and/or CO

2

 room 

sensor(s). The device can be fitted with a MOTORLESS 

cooker hood. This discharges cooking odours and humidity 
to the exterior via the central device.

It is not permitted to connect a cooker hood with 
motor or clothes dryer to the system.

Depending on the size of the home, the installer can 
set the system to deliver the correct volume of air. 

The ventilation system has four speed positions; absent, 

low, medium and high. These different setting options 

ensure that cooking odours and humidity are efficiently 

removed from the home. The MVS-15RH system was 
designed to operate 24 hours per day. The device is 

equipped with a highly energy-efficient EC motor to keep 

energy consumption to a minimum.

3. Operating the system:

For the device to function properly, the following conditions 
must be respected.

•  Ensure that sufficient air can be fed through transom 

windows or intake grilles.

•  If your home is fitted with non-closable air inlet openings, 

do not seal them or cover them with tape.

Summary of Contents for MVS-15RH




























Reviews: