User manual
We will replace products afflicted with manufacturing defects within 30
days of purchase and repair a light free of charge within 24 months of
purchase if problems develop under normal use; if repair is required
after 24 months from the date of purchase, we will charge for parts. The
total repair fee is dictated by the cost of the replaced materials.
PRODUCT FEATURES
PRODUCT INTRODUCTION
OPERATION INSTRUCTIONS
BATTERY REPLACEMENT
USAGE AND MAINTENANCE
PRODUCT WARRANTY
ORCATORCH D510 is a portable flashlight with a mechanically rotary
switch for technical diving use. The rotary switch offers high reliability
underwater. Using the latest USA CREE XM-L2(U2) LED, it can reach
900 lumens output. And using three C batteries, its runtime can be over
4 hours. Plus simple style appearance, robust water pressure resistant
construction, we believe it will be a reliable lighting tool for diving.
Tel:+86-755-33560383 Fax:+86-755-29454989
Email: [email protected] www.orcatorch.com
Address: 5th Floor, Emerson Building A,
26 Zone, Baoan District,
Shenzhen city,
China (518101)
Max
900
Lumens
Cree XM-L2(U2) LED, 900 lumens output
Uses 3*C batteries
Mechanically head rotary switch offers high reliability underwater
Water pressure resistant construction, depth rated to 150 meters
Standard included arm strap, fastens the light to your arm
High efficiency constant current circuit, constant brightness
Reverse polarity protection, to protect from improper battery
installation
Aircraft-grade high strength aluminum material
Premium Type III military hard-anodized seawater-corrosion-
resistance finish
Alloy aluminum reflector with professional optical analysis
Toughened glass with high water pressure resistance under deep
water
TECHNICAL PARAMETERS
Notice
: Stated data has been measured according to the international
flashlight test standards ANSI/NEMA FL1 using three C batteries under
laboratory conditions. The parameters are approximate and may vary
between flashlights, batteries, and environments.
ANSI/NEMA FL1
Output
Runtime
Intensity
Waterproof
Working voltage
Dimension
Net weight
Accessories
3 – 4.5 V
209mm(Length) x 35mm(Diameter) x 49mm(Head)
313g
（
excluding battery
）
O-ring lanyard, arm strap, silicone grease
,
Beam
Distance
Impact
Resistant
Mode
900 Lumens
4h
325m (on land)
26400cd
1m
under water 150m
1. ON/OFF: Insert the battery and tighten the light head to turn on the
flashlight, unscrew the light head to turn it off.
2. We recommend to tighten the light head to turn on the light before you
go underwater, and do not unscrew the light head until you have gone
out of water to avoid leaking underwater.
1. As shown in the figure, insert the battery with the anode side (+)
toward the light head.
2. Please do not reverse the battery to avoid damage to the flashlight
and battery.
3. Please do not use battery with higher voltage than the flashlight
working voltage.
4. Please do not use battery with damaged surface or deformation to
avoid short circuit, explosion, leakage, etc.
Reason A: The batteries need to be replaced.
Solution: Replace batteries (Please confirm correct installation of +
and - terminals).
Reason B: The threads, PCB board contact or other contacts are dirty.
Solution: Clean the contact points with an alcohol soaked cotton swab.
If the methods above don't work, please contact the distributors and
refer to the warranty policy.
²
into switch section or screw thread.
²
Tighten all the connections of the light before going underwater. For
head rotary switch flashlight, we recommend to tighten the light head to
turn on the light before you go underwater, and do not unscrew the light
head until you have gone out of water to avoid leaking underwater
²
Please don't disassemble the sealed head, doing so may cause
damage to the flashlight and will void the warranty.
²
We recommend the use of high quality batteries. If the flashlight will
not be used for a long time, remove the batteries to avoid damage from
electrolyte leakage or battery explosion.
²
Please replace the O-rings if they are damaged after prolonged use
and regularly lubricate the o-rings so as to not erode the rubber. Doing
so will keep the flashlight properly sealed against water.
²
Please clean the contacts of your light from time to time, especially
when the light flickers or doesn't light up. There are probably several
reasons for a flickering or not working light:
Do not drop or place the light on sand in case iron sand stick or go
Warning
The flashlight is high intensity lighting device and capable of causing
eye damage, please avoid shining the light directly into the eyes.
www.orcatorch.com
ORCATORCH TECHNOLOGY LIMITED
D510
²
Please clean the surface of the flashlight with fresh water after use in
case of the seawater corrosiveness.
