Oracle X7-8 Service Manual Download Page 92

Page: 92 / 308

Assign Serial Port Output Using SP Oracle ILOM CLI

Callout

Description

System/SMOD

Available On

Power connectors 0 and 1

System B –SMOD1

Always connect all four

power supplies. Connect to

200-240 VAC only.

Configuring Serial Port Sharing

By default, the NET MGT serial port connects to the SP console. Using Oracle ILOM, you can

configure the NET MGT serial port to connect to the host console instead. This feature is useful

for Windows kernel debugging, as it enables you to view non-ASCII character traffic from the

host console.

Do not configure the NET MGT port to connect to the host console until after you have

configured the Oracle ILOM network connection. Otherwise you cannot connect to Oracle

ILOM to switch it back.

For more details about restoring access to the server port on your server, see the Oracle

Integrated Lights Out Manager (ILOM) 4.0 Documentation Library at:

http://www.oracle.

com/goto/ilom/docs

You can assign serial port output using either the Oracle ILOM web interface or the command-

line interface (CLI). For instructions, see the following sections:

■

“Assign Serial Port Output Using SP Oracle ILOM CLI” on page 92

■

“Assign Serial Port Output (Oracle ILOM Web Interface)” on page 93

Assign Serial Port Output Using SP Oracle ILOM CLI

Open an SSH session and at the command line log in to the SP Oracle ILOM CLI.

ssh root@

ipaddress

where

ipaddress

is the IP address of the server SP.

For more information, see

“Using Oracle ILOM” in

Oracle Server X7-8 Installation Guide

The Oracle ILOM CLI prompt appears:

To set the serial port owner, type:

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands