Oracle X7-8 Service Manual Download Page 290

Page: 290 / 308

BIOS Boot Menu Selections

BIOS IO Menu Add-in Cards Options

The following table describes the BIOS IO Menu add-in cards options.

Setup Options

Options

Defaults

Description

Slot 1

Displays and provides options

to change the settings of the

devices in PCIe HBA slots.

IO Enable

Disabled/Enabled

Enabled

IO Enable

PCI-E UEFI Driver Enable

Disabled/Enabled

Enabled

Enable or disable PCI-E UEFI

Driver. If set to enabled, UEFI

Driver for the card executes as

normal. If set to disabled, UEFI

Driver for the card is not copied

into memory and the execution

of the UEFI Driver is inhibited.

Hot Plug Capable

Disabled/Enabled

Enabled

Specifies if the link is Hot-Plug

capable.

Slot 2 through Slot 16

Same description as Slot 1.

Related Information

■

“BIOS Main Menu Selections” on page 269

■

“BIOS Advanced Menu Selections” on page 274

■

“BIOS Boot Menu Selections” on page 290

■

“BIOS Save and Exit Menu Selections” on page 292

BIOS Boot Menu Selections

This section includes a screen of the BIOS Boot Menu. The options that are available from the

Boot Menu are described in the table that follows.

290

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands