manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 213

Remove an Internal USB Flash Drive

15.

Prepare the server for operation. See 

“Returning the Server to

Operation” on page 237

.

Related Information

■

“Install an SMOD” on page 197

Servicing the Internal USB Flash Drives

This section contains procedures for accessing and servicing a USB flash drive installed in the

SMOD internal USB ports.

■

“Remove an Internal USB Flash Drive” on page 213

■

“Install an Internal USB Drive” on page 214

Note - 

Internal USB ports are not used.

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

Remove an Internal USB Flash Drive

This is an internal component that is accessible from the back of the server by removing the

SMOD. Perform this procedure to access and remove internal SMOD USB flash drives.

1.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.

See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Remove the SMOD. See 

“Remove an SMOD” on page 195

.

3.

Set the SMOD on a flat surface with the front side facing toward you.

4.

Close the SMOD handles.

5.

Rotate the SMOD 180 degrees so the back (connector) side is facing toward you.

6.

Turn the SMOD upside down and locate the HBA card.

Note - 

The connector (back) side of the SMOD should still be facing you.

Servicing Components

213

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands