Oracle X7-2 Installation Manual Download Page 98

Page: 98 / 148

RAID Configuration Requirements

■

To install an OS, ensure that the drive where you want to install the OS is visible to the

system.

■

To install and boot an OS, you need to create a RAID volume on the drive.

■

If you do not want to use a RAID array, configure a drive as a RAID 0 volume.

■

You can use the BIOS RAID configuration utilities to configure RAID on the internal HBA

card. See

“Configuring RAID” on page 99

The following table lists the disk requirements for each supported RAID level:

RAID Level

Number of Disks Required

After you create a bootable RAID volume, install the OS. For details, refer to the operating

system installation guide in

http://www.oracle.com/goto/x7-2/docs

http://www.oracle.

com/goto/x7-2l/docs

RAID Configuration Requirements

Reconfiguring storage drives into RAID volumes is an optional task. Use the BIOS RAID

configuration utilities to configure RAID on the server.

You have the following options for configuring your server storage drives:

■

Option 1

– If you are going to install an operating system and you want to configure

multiple server storage drives into one or more RAID volumes, configure the server storage

drives into RAID volumes before you install the operating system.

■

Option 2

– If you are going to install an OS, but you do not want to configure the server

storage drives into RAID volumes, refer to the OS installation instruction in the

Oracle

Servers X7-2 and X7-2L Operating Systems Installation Guide

For information on creating RAID volumes after installing an operating system, refer to

the

Oracle X7 Series Servers Administration Guide

http://www.oracle.com/goto/

x86admindiag/docs

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands