Oracle X7-2 Installation Manual Download Page 52

Page: 52 / 148

Install the Server Into the Slide-Rail Assemblies

■

“Mark the Rackmount Location” on page 46

■

“Install the Server Into the Slide-Rail Assemblies” on page 52

Install the Server Into the Slide-Rail Assemblies

Use this procedure to install the server chassis with mounting brackets into the slide-rail

assemblies that are mounted to the rack.

Caution -

Personal Injury or Equipment Damage

: This procedure requires a minimum of

two people because of the weight of the server. Attempting this procedure alone could result in

equipment damage or personal injury.

Caution -

Personal Injury or Equipment Damage

: Always load equipment into a rack from

the bottom up so that the rack does not become top-heavy and tip over. Extend the rack anti-tilt

bar to prevent the rack from tipping during equipment installation.

Push the slide-rails as far as possible into the slide-rail assemblies in the rack.

Position the server so that the back ends of the mounting brackets are aligned

with the slide-rail assemblies that are mounted in the rack.

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands