Oracle X7-2 Installation Manual Download Page 136

Page: 136 / 148

Resources for Troubleshooting and Diagnostics

Auto Service Request

Oracle Auto Service Request (ASR) is provided to customers that have Oracle Premier

Support. Oracle ASR is the fastest way to restore system availability if a hardware fault occurs.

Oracle ASR software is secure and customer installable, with the software and documentation

downloadable from My Oracle Support at

https://support.oracle.com

. For instructions on

downloading the ASR software, refer to the knowledge article doc ID 1185493.1.

When a hardware fault is detected, Oracle ASR automatically opens a service request with

Oracle and transfers electronic fault telemetry data to help expedite the diagnostic process.

Oracle diagnostics analyze the telemetry data for known issues and delivers immediate

corrective actions. For security, the electronic diagnostic data sent to Oracle includes only what

is needed to solve the problem. The software does not use any incoming Internet connections

and does not include any remote access mechanisms.

For more information about Oracle ASR, go to:

http://www.oracle.com/support/premier/

auto-service-request.html

136

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands