manualshive.com logo in svg

Oracle Tekelec 1200, Installation Manual

Share
Download
Oracle Tekelec 1200 Installation Manual Download Page 44

Procedure — Receiving Shipping Container for the Cabinet

Danger:  At least two people are required to safely move and position the cabinets. Read
and understand this procedure completely before continuing.

1. Before opening any shipping container, inspect it for evidence of damage during shipment.

Report any damage to the carrier for investigation and possible claims. Also report any damage
to the site supervisor.

2. Check the packing slips against the equipment specification list for this installation site.

Report any discrepancies.

Procedure — Unpacking the Container for the Cabinet

Danger:  At least two people are required to safely move and position the cabinets. Read
and understand this procedure completely before continuing.

1. Open crate door with integrated ramp by opening draw latches.

Use the crate door with integrated ramp to remove the cabinet from the shipping compartment.
(See 

Figure 19: Integrated Crate Ramp

). See 

Figure 18: Draw Latch on Crate

 and 

Figure 19: Integrated

Crate Ramp

.

Figure 18: Draw Latch on Crate

44

910-5681-001 Revision E, February 2014

Cabinet Installation

Installation

Summary of Contents for Tekelec 1200













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands