Oracle Sun Server X4-4 Installation Manual Download

Page: 72 / 148

Launch Oracle System Assistant Using the Oracle ILOM Web Interface

Launch Oracle System Assistant Using the Oracle ILOM

Web Interface

Before You Begin

You should have already set up Oracle ILOM for remote Ethernet access

“Connecting to Oracle

ILOM” on page 53

Ensure that the server is in standby power mode.

In server standby mode, the Power/OK indicator blinks slowly. See

“Front Panel

Features” on page 15

for the location of the Power/OK indicator.

Log in to the server SP Oracle ILOM web interface.

In your browser's address field, enter the server's SP IP address.
The System Summary screen appears.

Click the Oracle System Assistant Launch button in the upper right panel.

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands