Oracle Sun Server X4-4 Installation Manual Download

Page: 137 / 148

Use the Oracle ILOM CLI for Orderly Shutdown

Use the Oracle ILOM CLI for Orderly Shutdown

Log in to the Oracle ILOM command-line interface (CLI) using an Administrator

account.

Oracle ILOM displays the default command prompt (->), indicating that you have successfully

logged in to Oracle ILOM.

From the CLI prompt, type the following command:

stop /System

The server performs an orderly shutdown to standby power mode.

To completely power off the server from standby power mode, disconnect the

power cables from the server.

The server powers down completely.

See Also

■

“Use the Power Button for Orderly Shutdown” on page 136

■

“Use the Oracle ILOM Web Interface for Orderly Shutdown” on page 137

Use the Oracle ILOM Web Interface for Orderly

Shutdown

Log in to the Oracle ILOM web interface using an Administrator account.

The Oracle ILOM web interface System Information > Summary page appears.

In the left pane, click Host Management > Power Control, and select Graceful

Shutdown and Power Off from the Select Action list box.

Click Save, and then click OK.

The host server performs an orderly shutdown to standby power mode.

To completely power off the server from standby power mode, disconnect the

power cables from the server.

The server powers down completely.

See Also

■

“Use the Power Button for Orderly Shutdown” on page 136

■

“Use the Oracle ILOM CLI for Orderly Shutdown” on page 137

Controlling System Power and Viewing BIOS Messages

137

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands